Cisco 3200 Manuel d'utilisateur Page 235
- Page / 282
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
12-27
Cisco TelePresence System 3200
OL-14521-01
Chapter 12 Field-Replaceable Unit Guide
Replacing the Projector—Part Number CTS-PRJTR-GEN1=
d.
When you are prompted to reset the lamp counter, Select Yes and press the OK button.
e.
Select Yes and press the OK button to reconfirm your choice.
Replacing the Projector—Part Number CTS-PRJTR-GEN1=
Step 1
Power off the projector by turning off the power switch located on the back of the unit.
Step 2
Unplug the VGA cable, power cable and serial cable from the rear of the unit.
Step 3
Remove two of the six screws that hold the projector assembly to the underside of the center tabletop.
These screws are the rear-most of the six screws and the farthest away from the projector lens.
Step 4
Loosen the remaining four mounting screws.
Step 5
Remove the projector assembly by sliding the unit to the front until the projector mounting bracket
disengages from the loosened mounting screws.
Step 6
Remove the screws that attach the mounting plate to the projector and remove the plate.
Step 7
Attach the mounting plate to the replacement projector.
Step 8
Reattach the assembly to the underside of the tabletop.
Step 9
Reattach the VGA cable to the projector.
Step 10
Reattach the power cable to the projector.
Step 11
Reattach the serial cable to the auxiliary control unit.
Step 12
Power on the projector by turning on the power switch located on the back of the unit.
Step 13
Perform first-time setup procedures for the projector by completing the steps in the “Setting Up the
Projector” section on page 10-20.
Replacing a PDU—Part Number CTS-PWR-PDU=
There are seven PDUs in the following places:
•
Two PDUs attached to the left accessory cabinet
•
One PDU attached to the right accessory cabinet
•
One PDU attached to the underside of the first row tabletop, on the center privacy panel
•
One PDU in the cable gutter on the second row table section, Section 4 (second from the left)
•
One PDU in the cable gutter on the second row table section, Section 3 (second from the right)
Step 1
On the PDU to be replaced, turn the power switch to Off and remove the plug from the wall receptacle.
Step 2
Remove any cables plugged into the PDU.
- Assembly Guide 1
- Use & Care Guide 1
- Field-Replaceable Unit Guide 1
- Contents 3
- Introduction 9
- Conventions 9
- Guidelines 10
- Related Documentation 10
- Overview 11
- Chapter 1 Overview 12
- Chapter Organization 12
- Conventions and Terminology 13
- Tools and Equipment List 13
- Tools and Equipment List 14
- Building the Display Assembly 15
- Minimum 12 inches (30.5 cm) 24
- Minimum 24 inches 24
- Leveling Alignment Points 28
- Leveling Goals 28
- Accessory Cabinet 36
- Figure 4-2 Left Display shelf 38
- Figure 4-5 Accessory Cabinet 41
- Figure 5-8 Light Cup bracket 52
- Figure 5-15 Four L-brackets 59
- Privacy Panel Assembly 70
- 22 23 24 74
- OL-14521-01 100
- Parts List 100
- Figure 7-13 Second Row PDUs 104
- Figure 7-46 Cable Cover 133
- 59” (150 cm) 135
- Elements 137
- Switch Bracket 139
- Figure 8-1 Camera Assembly 140
- Figure 8-2 Projector Assembly 141
- Figure 8-3 Projector Assembly 142
- Figure 8-4 Projector Assembly 143
- Figure 8-5 Codec Assembly 144
- Figure 8-6 Codec Assembly 145
- Figure 8-7 Codec Assembly 146
- Figure 8-8 Speaker Assembly 147
- Figure 8-9 Speaker Assembly 148
- Figure 8-10 Speaker Assembly 149
- Parts List 155
- Table Leg Power 160
- Projector Power 160
- Table Leg Signal 161
- IP Phone Signal 161
- Microphone Signal 161
- Projector Signal 161
- VGA Peripheral 161
- Floor-mounted junction box 164
- Table segment 166
- RJ45 Power over Ethernet 170
- HDMI connector 170
- Primary Codec 176
- Auxiliary Control Unit 176
- Projector 176
- Presentation Codec 177
- First-Time Setup 183
- Figure 10-1 Bootup Completed 184
- Setting Up CTS Components 186
- Setting Up the Displays 187
- Setting Up the Cameras 188
- Starting the Software Setup 189
- Setting Up CTS Components 190
- Adjusting the Zoom 191
- Focusing the Camera 194
- Large target 195
- Small target 195
- Focus ring 196
- Zoom ring 196
- Troubleshooting Cameras 198
- Setting Up the Speakers 200
- Setting Up the Microphones 200
- Troubleshooting Microphones 201
- Setting Up the Projector 202
- Other Devices 205
- Cleaning the Camera lens 208
- Maintaining the Projector 208
- Powering On the System 212
- CTS3K-CAM-CLST-G2= 213
- CTS-DISP-65-GEN4= 214
- Removing Audio Components 215
- Removing the Camera Cluster 216
- Removing the Left Door 216
- Removing a Display Shelf 216
- On/Off Switch 220
- AC inlet 220
- Powering Off the System 226
- Replacement Bulbs 230
- Replacing a Light Fixture 230
- CTS-AV-EXP= 231
- CTS-LIGHT-CTRL= 232
- CP-7975G-CTS= 233
- Replacing the Projector Lamp 233
- Replacing a Display Shelf 236
- Replacing a Display Shelf 237
- 53-2855-xx 245
- CTS3K-ACC2-KIT 247
- CTS3K-CAM-CLST-G2 248
- CTS32-ACC-KIT 252
- CTS32-M-2TBL-G2, 69-1853-xx 253
- CTS-CODEC-SEC 258
- CTS3K-FUR-MAPLE 260
- CTS3K-LIGHT-STR 260
- Equipment 265
- Asia Pacific 266
- Argentina 267
- Australia 268
- Central Europe 269
- China 270
- India, UAE, South Africa 271
- Israel 272
- Italy 273
- Japan 274
- North America 275
- Switzerland 276
- United Kingdom 277
- United Kingdom 278
- Dimensions and Description 279
Produits connexes et manuels pour Accessoires pour ordinateurs Cisco 3200
(120 pages)
(74 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.404 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels