Cisco 3200 Manuel d'utilisateur Page 202
- Page / 282
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
10-20
Cisco TelePresence System 3200
OL-14521-01
Chapter 10 First-Time Setup
Setting Up CTS Components
Setting Up the Projector
To set up the projector, complete the following steps:
Step 1
Make sure that a serial cable is connected from your projector to the Serial output of the auxiliary control
unit. See
Chapter 9, “Routing Power and Signal Cables” for information about cabling your system with
an Auxiliary Control Unit.
Step 2
Start a test pattern display for the projector by completing the following steps:
a.
Open a browser that is connected to the network.
b.
Enter the IP address of the primary codec to log in to Cisco TelePresence System Administration.
c.
Select Troubleshooting > Hardware Setup, then click the Presentation Devices radio button.
d.
Select the Test Pattern radio button.
e.
Click Start to begin the test.
Step 3
Turn on the projector by turning the projector power rocker switch to the ON position.
No sound registers. Microphone cable is not
connected or is only partially
connected.
Check that the system is plugged
in and power is on.
Check that the microphone plug
is firmly seated in the correct
connector on the primary codec.
Check that the mute light on each
microphone is lit. An unlit light
indicates that the microphone is
not plugged in.
Lightly tap the microphone to
see if sound registers.
Contact Cisco technical support
if you are certain that the cabling
is correct and power is applied to
the system, but no sound
registers on the microphone.
Microphone icon with red pipe
displays.
Microphone is not connected. Check that the microphone is
properly plugged in.
Microphone icon with question
mark displays.
One of the microphones is
unplugged.
Check that the microphone is
properly plugged in.
System is experiencing
“phantom switching” (during a
TelePresence conference, the
system switches to a segment
where no one is talking or is
empty)
Microphone is not properly
calibrated.
Rerun the Microphone
Calibration procedure.
Table 10-4 Troubleshooting Chart for Microphone Problems (continued)
Problem Possible Cause Possible Solution
- Assembly Guide 1
- Use & Care Guide 1
- Field-Replaceable Unit Guide 1
- Contents 3
- Introduction 9
- Conventions 9
- Guidelines 10
- Related Documentation 10
- Overview 11
- Chapter 1 Overview 12
- Chapter Organization 12
- Conventions and Terminology 13
- Tools and Equipment List 13
- Tools and Equipment List 14
- Building the Display Assembly 15
- Minimum 12 inches (30.5 cm) 24
- Minimum 24 inches 24
- Leveling Alignment Points 28
- Leveling Goals 28
- Accessory Cabinet 36
- Figure 4-2 Left Display shelf 38
- Figure 4-5 Accessory Cabinet 41
- Figure 5-8 Light Cup bracket 52
- Figure 5-15 Four L-brackets 59
- Privacy Panel Assembly 70
- 22 23 24 74
- OL-14521-01 100
- Parts List 100
- Figure 7-13 Second Row PDUs 104
- Figure 7-46 Cable Cover 133
- 59” (150 cm) 135
- Elements 137
- Switch Bracket 139
- Figure 8-1 Camera Assembly 140
- Figure 8-2 Projector Assembly 141
- Figure 8-3 Projector Assembly 142
- Figure 8-4 Projector Assembly 143
- Figure 8-5 Codec Assembly 144
- Figure 8-6 Codec Assembly 145
- Figure 8-7 Codec Assembly 146
- Figure 8-8 Speaker Assembly 147
- Figure 8-9 Speaker Assembly 148
- Figure 8-10 Speaker Assembly 149
- Parts List 155
- Table Leg Power 160
- Projector Power 160
- Table Leg Signal 161
- IP Phone Signal 161
- Microphone Signal 161
- Projector Signal 161
- VGA Peripheral 161
- Floor-mounted junction box 164
- Table segment 166
- RJ45 Power over Ethernet 170
- HDMI connector 170
- Primary Codec 176
- Auxiliary Control Unit 176
- Projector 176
- Presentation Codec 177
- First-Time Setup 183
- Figure 10-1 Bootup Completed 184
- Setting Up CTS Components 186
- Setting Up the Displays 187
- Setting Up the Cameras 188
- Starting the Software Setup 189
- Setting Up CTS Components 190
- Adjusting the Zoom 191
- Focusing the Camera 194
- Large target 195
- Small target 195
- Focus ring 196
- Zoom ring 196
- Troubleshooting Cameras 198
- Setting Up the Speakers 200
- Setting Up the Microphones 200
- Troubleshooting Microphones 201
- Setting Up the Projector 202
- Other Devices 205
- Cleaning the Camera lens 208
- Maintaining the Projector 208
- Powering On the System 212
- CTS3K-CAM-CLST-G2= 213
- CTS-DISP-65-GEN4= 214
- Removing Audio Components 215
- Removing the Camera Cluster 216
- Removing the Left Door 216
- Removing a Display Shelf 216
- On/Off Switch 220
- AC inlet 220
- Powering Off the System 226
- Replacement Bulbs 230
- Replacing a Light Fixture 230
- CTS-AV-EXP= 231
- CTS-LIGHT-CTRL= 232
- CP-7975G-CTS= 233
- Replacing the Projector Lamp 233
- Replacing a Display Shelf 236
- Replacing a Display Shelf 237
- 53-2855-xx 245
- CTS3K-ACC2-KIT 247
- CTS3K-CAM-CLST-G2 248
- CTS32-ACC-KIT 252
- CTS32-M-2TBL-G2, 69-1853-xx 253
- CTS-CODEC-SEC 258
- CTS3K-FUR-MAPLE 260
- CTS3K-LIGHT-STR 260
- Equipment 265
- Asia Pacific 266
- Argentina 267
- Australia 268
- Central Europe 269
- China 270
- India, UAE, South Africa 271
- Israel 272
- Italy 273
- Japan 274
- North America 275
- Switzerland 276
- United Kingdom 277
- United Kingdom 278
- Dimensions and Description 279
Produits connexes et manuels pour Accessoires pour ordinateurs Cisco 3200
(120 pages)
(74 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels