Cisco 3200 Manuel d'utilisateur Page 212
- Page / 282
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
12-4
Cisco TelePresence System 3200
OL-14521-01
Chapter 12 Field-Replaceable Unit Guide
Powering On the System
Powering On the System
Use this procedure for sections in this chapter that require you to power on the system.
Step 1
If you replaced the primary codec, reconfigure the codec for the new MAC address in
Cisco Unified Communications Manager by performing the following actions:
a.
Log in to Cisco Unified Communications Manager.
b.
Change the device MAC address to the MAC address for the new primary codec. The MAC address
should be displayed on the codec.
Step 2
Power on the Cisco TelePresence 3200 by turning the power switches to the On position on the two left
PDUs, single right PDU, and auxiliary control unit.
Six check boxes display on the lower left corner of the center display screen.
Step 3
Wait while the system checks each check box and clears the screen.
The system IP address displays on the lower right corner of the center display screen.
Step 4
Write down the IP address. This is the address of the primary codec.
Step 5
Log in to the system by entering the following information:
a.
In the Admin field, type admin.
b.
In the Password field, type cisco.
Note
If your administrator has changed the user name or password, enter those values.
Step 6
Click Login.
Step 7
Verify the status of the Cisco Unified Communications Manager (seen in the lower left portion of the
window) is Enabled/Up.
Step 8
Select Hardware Setup to verify the cameras, displays, speakers, and microphones are working
properly.
Step 9
If you are replacing a primary codec, perform the following steps:
Note
If you are not replacing a primary codec, do not perform the following steps.
a.
Navigate to the Device Information > Configuration > CUCM settings window, then perform the
following actions:
b.
In the Certificate Trust List (CTL) area, delete the CTL from your system by clicking Delete CTL.
c.
In the Use Configuration TFTP Server area, click Automatic to set TFTP conditions to their default
value and remove any alternate TFTP servers.
- Assembly Guide 1
- Use & Care Guide 1
- Field-Replaceable Unit Guide 1
- Contents 3
- Introduction 9
- Conventions 9
- Guidelines 10
- Related Documentation 10
- Overview 11
- Chapter 1 Overview 12
- Chapter Organization 12
- Conventions and Terminology 13
- Tools and Equipment List 13
- Tools and Equipment List 14
- Building the Display Assembly 15
- Minimum 12 inches (30.5 cm) 24
- Minimum 24 inches 24
- Leveling Alignment Points 28
- Leveling Goals 28
- Accessory Cabinet 36
- Figure 4-2 Left Display shelf 38
- Figure 4-5 Accessory Cabinet 41
- Figure 5-8 Light Cup bracket 52
- Figure 5-15 Four L-brackets 59
- Privacy Panel Assembly 70
- 22 23 24 74
- OL-14521-01 100
- Parts List 100
- Figure 7-13 Second Row PDUs 104
- Figure 7-46 Cable Cover 133
- 59” (150 cm) 135
- Elements 137
- Switch Bracket 139
- Figure 8-1 Camera Assembly 140
- Figure 8-2 Projector Assembly 141
- Figure 8-3 Projector Assembly 142
- Figure 8-4 Projector Assembly 143
- Figure 8-5 Codec Assembly 144
- Figure 8-6 Codec Assembly 145
- Figure 8-7 Codec Assembly 146
- Figure 8-8 Speaker Assembly 147
- Figure 8-9 Speaker Assembly 148
- Figure 8-10 Speaker Assembly 149
- Parts List 155
- Table Leg Power 160
- Projector Power 160
- Table Leg Signal 161
- IP Phone Signal 161
- Microphone Signal 161
- Projector Signal 161
- VGA Peripheral 161
- Floor-mounted junction box 164
- Table segment 166
- RJ45 Power over Ethernet 170
- HDMI connector 170
- Primary Codec 176
- Auxiliary Control Unit 176
- Projector 176
- Presentation Codec 177
- First-Time Setup 183
- Figure 10-1 Bootup Completed 184
- Setting Up CTS Components 186
- Setting Up the Displays 187
- Setting Up the Cameras 188
- Starting the Software Setup 189
- Setting Up CTS Components 190
- Adjusting the Zoom 191
- Focusing the Camera 194
- Large target 195
- Small target 195
- Focus ring 196
- Zoom ring 196
- Troubleshooting Cameras 198
- Setting Up the Speakers 200
- Setting Up the Microphones 200
- Troubleshooting Microphones 201
- Setting Up the Projector 202
- Other Devices 205
- Cleaning the Camera lens 208
- Maintaining the Projector 208
- Powering On the System 212
- CTS3K-CAM-CLST-G2= 213
- CTS-DISP-65-GEN4= 214
- Removing Audio Components 215
- Removing the Camera Cluster 216
- Removing the Left Door 216
- Removing a Display Shelf 216
- On/Off Switch 220
- AC inlet 220
- Powering Off the System 226
- Replacement Bulbs 230
- Replacing a Light Fixture 230
- CTS-AV-EXP= 231
- CTS-LIGHT-CTRL= 232
- CP-7975G-CTS= 233
- Replacing the Projector Lamp 233
- Replacing a Display Shelf 236
- Replacing a Display Shelf 237
- 53-2855-xx 245
- CTS3K-ACC2-KIT 247
- CTS3K-CAM-CLST-G2 248
- CTS32-ACC-KIT 252
- CTS32-M-2TBL-G2, 69-1853-xx 253
- CTS-CODEC-SEC 258
- CTS3K-FUR-MAPLE 260
- CTS3K-LIGHT-STR 260
- Equipment 265
- Asia Pacific 266
- Argentina 267
- Australia 268
- Central Europe 269
- China 270
- India, UAE, South Africa 271
- Israel 272
- Italy 273
- Japan 274
- North America 275
- Switzerland 276
- United Kingdom 277
- United Kingdom 278
- Dimensions and Description 279
Produits connexes et manuels pour Accessoires pour ordinateurs Cisco 3200
(120 pages)
(74 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.833 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels