INSTALL THE HARDWARECONNECT THE RSPSTART AND CONFIGURE THE SYSTEMINSTALL FIELD REPLACEABLE UNITS (FRUS)12345Quick Start GuideIs Cisco documentation he
8Mount the Chassis in the RackInstall the HardwareH2298Warning Two people are required toperform this step.Step 1 Slowly lift the chassis in unison. L
9Remove the Chassis FootInstall the HardwareUnderside of chassisChassis footChassis foot removal 7/16" nutFlat-blade screwdriverslot for removin
10Install Interface Processors, Fillers, VIPs, or RSPsInstall the HardwareCard carrier guide (black)Captiveinstallationscrew53375ABCTheRouteSwitchProc
11Install Power Supplies in the RouterInstall the HardwareThis procedure applies to AC-input and DC-inputpower supplies, with differences clearly note
12Step 5 Use a screwdriver to tighten the captive installation screw on the top of the power supply.Note For DC-input power supplies, refer to the “In
13Install the DC-Input Power SupplyInstall the HardwareR TO BE FULLY ENGAGEDOPERATING POWER SUPPLYallation screws l block cover IOOUT FAILINPUT POWERD
14Note Perform Step 1 through Step 5 on the previous page before following the steps below.Step 1 Using a screwdriver, loosen the captive installation
15Connect the RSPConnect the Console PortThe system console port on the RSP is a DB-25receptacle DCE port for connecting a data terminal,which allows
16Connect the Console and the Auxiliary Y-CablesConnect the RSPThe console and auxiliary Y-cables allow you tosimultaneously connect the console or au
17Step 1 Check the following components to make sure they are secure:• Each interface processor is inserted all the way into its slot, and captive ins
18Start and Configure the SystemStart a Basic ConfigurationMany privileged-level EXEC commands are used toset operating parameters. To enter theprivileg
19Perform a Basic Configuration Using SetupStart and Configure the SystemNote Therouter’sserial(WAN)cableshouldnotbeconnected to the CSU/DSU unless you
20Step 7 Enter yes or press Return toconfigure IP, and then select an interior routing protocolfor IP, if you areusing IP routing:Configure IP? [yes]:
21Start and Configure the SystemConfigure an Ethernet InterfaceStep 1 To configure your system for an EthernetLAN, respond to the prompts as follows,usin
22Step 4 At the # prompt, enter the copy running-config startup-config command to save the configuration toNVRAM as follows:Hostname# copy running-config
23Perform a Basic Configuration Using Configuration ModeStart and Configure the SystemAt the reboot, the following example appears:Any interface listed w
24Flash Memory CardsInstall Field Replaceable Units (FRUs)A Flash memory card that ships with your Cisco7507 contains the Cisco IOS software image to
25TheRSP hastwo PCCard slots—slot 0 and slot 1—into whichyou caninstall aFlash memorycard. Inthe RSP2,RSP4, and RSP8, the orientation is vertical. PC
26Format a Flash Memory CardInstall Field Replaceable Units (FRUs)Flash memory cards shipped as spare parts must beformatted. Use only Intel Series 2+
27Make a Flash Memory Card Image BootableInstall Field Replaceable Units (FRUs)Note In this example, the filename is new.image,and the Flash memory car
1Install the HardwareENABLEENABLEEJECTSLOT 0SLOT 1NORMALCPU HALTRESETAUX.CONSOLEROUTE SWITCH PROCESSOR 2SLAVEMASTERSLAVE/MASTERH3888Slot 01234 5 6Uppe
28Install Field Replaceable Units (FRUs)Prepare to Remove and Installan RSPTo remove and install an RSP, you will perform thefollowing steps:• Copy th
29Remove and Install an Interface Processor, Filler, VIP, or RSPInstall Field Replaceable Units (FRUs)53376STOP!on contactBottom ejector leverCaptive
30Install Field Replaceable Units (FRUs)Step 8 If you have a VIP4 and are using HSAwith an RSP2 as the slave processor, wait20-30 seconds, then reinse
31Check the Interface Processor or VIP InstallationInstall Field Replaceable Units (FRUs)Note When a new VIP is inserted or when a VIP ismoved to a ne
32Copy the Configuration File for an RSPInstall Field Replaceable Units (FRUs)Refer to the appropriate Cisco IOS software documentation for the configur
33Step 6 Enter the name or IP address of the remote host. In the following example, the name of the remoteserver is servername:Router# copy startup-co
34Step 7 Enter the name of the configuration file. The default is to use the name of the router with the suffix-confg. Press Return to accept the default
35Retrieve the Configuration File for RSPsRetrieve the saved configuration and copy it to NVRAM by accessing the router through a console terminal, orfr
36The console display indicates whether or not the operation was successful. A series of exclamation points (!!!!)and [OK] (as shown in the preceding
37Remove and Install Port AdaptersInstall Field Replaceable Units (FRUs)ScrewUpper edgeLower edgeCarrierAB
2Prepare to Install the RouterInstall the HardwareNote For detailed hardware installationinstructions and safety guidelines, refer to the Cisco7500 Se
38Note First remove the VIP from the chassis before removing the port adapter from the VIP. See the “Removeand Install an Interface Processor, Filler,
39Remove and Replace the Power SupplyRedundant power supplies support online insertion and removal (OIR); if you remove one power supply, thesecondpow
40For the DC-input power supply: Use a screwdriver to loosen the captive installation screws on theterminal block cover, lift the cover, use the wire
78-13034-01Printed in the USA on recycled paper containing 10% postconsumer waste.Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jo
3Install the RouterInstall the HardwareENABLEENABLEEJECTSLOT 0SLOT 1NORMALCPU HALTRESETAUX.CONSOLEROUTE SWITCH PROCESSOR 2SLAVEMASTERSLAVE/MASTERIODC
4Rack-Mount the Router (Optional)Install the Hardware53423M4 x 10-mm long Phillipsflat-head screws (to attachears to chassis)10-32 x 5/8-inch long Phi
5Mount Brackets to the Rack PostsInstall the Hardware53382Rack postFlangeShielded sideNote The distance between the inner edges of theleft and right r
6Secure the SpacersInstall the Hardware53380ABCStep 1 Loosen the 10-32 x 5/8-inch LG Phillipspan-head screw at the end of the ledge ofthe right-side b
7Attach the Chassis EarsInstall the HardwareH2297ORCenter-mountpositionFlush-mountpositionStep 1 Position the ears on the chassis as follows:• To flush
Commentaires sur ces manuels