Cisco 2525 Guide de l'utilisateur Page 73
- Page / 166
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring the Cisco 2524 and Cisco 2525 Routers 4-11
Configuring the Router
The ISDN BRI interface is configured to allow connection to ISDN WANs. To configure
the ISDN BRI interface, respond as follows (using your addresses and subnet mask) to the
setup prompts, substituting the correct addresses and host names as appropriate:
Configuring interface BRI0:
Is this interface in use? [yes]
Configure IP on this interface? [yes]
IP address for this interface: 172.16.71.1
Number of bits in subnet field [0]: 8
lass B network is 172.16.0.0, 8 subnet bits; mask is
255.255.255.0
Configure AppleTalk on this interface? [no]: yes
Extended AppleTalk network? [no]: yes
AppleTalk starting cable range [0]: 1
AppleTalk ending cable range [1]: 2
AppleTalk zone name [myzone]:
AppleTalk additional zone name: otherzone
AppleTalk additional zone name:
Configure IPX on this interface? [no]: yes
IPX network number [1]: B000
Configuring the Ethernet or Token Ring Interfaces
Take the following steps to configure the Ethernet or Token Ring interface to allow
communication over a LAN. To configure the interface parameters, you need to know your
Ethernet or Token Ring interface network addresses. In this example, the system is being
configured for an Ethernet LAN using IP.
Step 1 Respond as follows (using your addresses and subnet mask) to the setup prompts,
substituting the correct addresses and host names as appropriate:
Configuring interface Ethernet0:
Is this interface in use? [yes]:
Configure IP on this interface? [yes]:
IP address for this interface: 172.16.72.1
Number of bits in subnet field [8]: 8
Class B network is 172.16.0.0, 8 subnet bits; mask is
255.255.255.0
- About This Guide 1
- Document Organization 2
- Document Conventions 3
- Safety Warnings.”) 4
- Overview of the Cisco 2524 5
- Features 10
- Specifications 11
- FCC Part 68 13
- Preparing to Install the 15
- Cisco 2524 and Cisco 2525 15
- Safety Recommendations 16
- Site Environment 18
- Preventive Site Configuration 18
- Configuring Equipment Racks 19
- Power Supply Considerations 19
- Installation Checklist 20
- Creating a Site Log 22
- 1. kHz = kilohertz 23
- ISDN Connections 26
- 1. nF = nanoFarad 27
- Ethernet Connections 29
- Token Ring Connections 29
- Console Port Connections 30
- Auxiliary Port Connections 30
- Inspecting the System 31
- Installing the Cisco 2524 and 33
- Required Tools and Parts 34
- Setting Up the Chassis 35
- Rack-Mounting the Chassis 36
- Attaching the Brackets 37
- Figure 3-6 or Figure 3-7 38
- Figure 3-8 or Figure 3-9 39
- Installing in a Rack 40
- Wall-Mounting the Chassis 41
- SERIAL 1 42
- SERIAL 0 42
- DC Power Specifications 43
- Wiring the DC Power Supply 44
- Input: –40––72V 45
- Current: 1.5–1.0A 45
- Watts: 40W 45
- Connecting to the Network 46
- Connecting to a WAN 51
- Figure 3-20.) 52
- Figure 3-21.) 53
- Figure 3-22.) 54
- ACTIVITY 55
- Console port 59
- RJ-45 roll-over cable 59
- RJ-45-to-DB-25 adapter 59
- Configuring the Cisco 2524 and 63
- Configuring the Router 64
- Using Configuration Mode 65
- Using AutoInstall 66
- Configuring the Router 67
- Configuring ISDN 76
- Configuring Switched 56 78
- Configuring DDS 79
- Specifying the Boot Method 82
- Getting More Information 84
- Cabling Specifications for the 85
- Identifying a Roll-Over Cable 86
- Pin 1 and pin 8 87
- (labeled Terminal) 88
- (labeled Modem) 89
- Token Ring Port Pinouts 93
- RJ-48C jack 94
- EIA/TIA-232 97
- EIA/TIA-449 99
- <— indicates DCE to DTE 102
- APPENDIX 109
- Running Diagnostic Tests 111
- Getting Help 111
- Cisco 2525 Routers 113
- Installing WAN Modules 114
- Opening the Chassis 115
- Tools Required 116
- Removing the Chassis Cover 116
- Screw Slot 117
- Flat-blade screwdriver 117
- CODE0CODE1 118
- Upgrading the DRAM SIMM 119
- Tools and Equipment Required 121
- DRAM SIMM Installation 121
- System-Code SIMM Replacement 123
- Replacing the Cover 126
- Recovering Lost Passwords 127
- (Router#): 132
- > b [tftp] flash filename 134
- Translated Safety Warnings 141
- Product Disposal Warning 142
- Jewelry Removal Warning 143
- Ground Connection Warning 144
- Installation Warning 145
- TN Power Warning 146
- Circuit Breaker (15A) Warning 146
- SELV Circuit Warning 148
- ISDN Connection Warning 152
- Qualified Personnel Warning 154
- Restricted Area Warning 155
- DC Power Supply Warning 159
- DC Power Connection Warning 160
- Lightning Activity Warning 161
- Grounded Equipment Warning 162
- Power Supply Warning 164
Produits connexes et manuels pour Mise en réseau Cisco 2525
(74 pages)
Mise en réseau Cisco 1710 Spécifications
(88 pages)
(88 pages)
(139 pages)
(164 pages)
Mise en réseau Cisco PA-T3 Spécifications
(74 pages)
(74 pages)
Kenwood MFJ-286 manuels
Manuels d'utilisation et guides de l'utilisateur pour Microphones Kenwood MFJ-286.
Nous fournissons des manuels en pdf 1 Kenwood MFJ-286 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels