Cisco Cisco Aironet Wireless LAN Client Spécifications Page 72
- Page / 142
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-10
Cisco Aironet Wireless LAN Client Adapters Installation and Configuration Guide for Linux
OL-1376-02
Chapter 5 Advanced Configuration
Overview
Table 5-4 RF Network Parameters
Parameter Description
Data Rate Specifies the rate at which you want your client adapter to transmit or
receive packets to or from access points (in infrastructure mode) or
other clients (in ad hoc mode).
We recommend Auto Rate Selection for infrastructure mode; setting a
specific data rate is recommended for ad hoc mode.
Default: Auto Rate Selection
Data Rate Description
Auto Rate Selection Uses the 11-Mbps data rate when possible
but drops to lower rates when necessary.
1 Mbps Only Offers the greatest range but the lowest
throughput.
2 Mbps Only Offers less range but greater throughput
than the 1 Mbps Only option.
5.5 Mbps Only Offers less range but greater throughput
than the 2 Mbps Only option.
11 Mbps Only Offers the greatest throughput but the
lowest range.
Note Your client adapter’s data rate must be set to Auto Rate
Selection or must match the data rate of the access points (in
infrastructure mode) or the other clients you wish to
communicate with (in ad hoc mode). Otherwise, your client
adapter might not be able to associate to them.
Use Short Radio Headers Selecting this check box sets your client adapter to use short radio
headers. However, the adapter uses short radio headers regardless of
how the access point is configured. Short radio headers improve
throughput performance; long radio headers ensure compatibility with
clients and access points that do not support short radio headers.
Default: Deselected
World Mode Selecting this check box enables the client adapter to assume the legal
transmit power level and channel set of the access point to which it is
associated. This parameter is available only in infrastructure mode and
is designed for users who travel between countries because it allows the
adapter to be used in different regulatory domains.
Default: Deselected
Note When World Mode is enabled, only the transmit power levels
supported by the country of operation’s regulatory agency are
available.
- Guide for Linux 1
- CONTENTS 3
- Contents 4
- 5 Advanced Configuration 5-1 5
- 6 Diagnostics 6-1 5
- 7 Routine Procedures 7-1 5
- 8 Troubleshooting 8-1 6
- Japanese Translation D-7 7
- English Translation D-7 7
- Audience 10
- Organization 10
- Conventions 11
- Attention 12
- Avvertenza 12
- Advarsel 12
- Related Publications 13
- Obtaining Documentation 13
- Ordering Documentation 14
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 15
- Cisco TAC Escalation Center 16
- Overview 17
- Terminology 18
- Parts of the Client Adapter 19
- Chapter 1 Overview 20
- Ad Hoc Wireless LAN 21
- Site Survey 22
- Preparing for Installation 25
- Safety Information 26
- Unpacking the Client Adapter 27
- System Requirements 27
- Site Requirements 28
- PCMCIA Installation 32
- Enter (Figure 3-3) 33
- Figure 3-7 Make All Screen 37
- Option 1 for Red Hat Systems 38
- Option 2 for Red Hat Systems 39
- Verifying Installation 41
- Inserting a PC Card 42
- Additional Procedures 44
- Opening the Client Utilities 46
- Selecting the Radio 47
- Enabling LEAP 52
- Using the Bcard Utility 53
- Finishing the Installation 54
- Enabling Security Features 55
- Server-Based Authentication 56
- Getting Started 56
- Changing the Password 56
- Entering a New WEP Key 57
- Selecting an Existing WEP Key 59
- Enabling WEP 59
- Message Integrity Check (MIC) 60
- Advanced Configuration 63
- Setting Enterprise Parameters 65
- Table 5-2 System Parameters 66
- Network Type Description 67
- Authentication Description 69
- Setting RF Network Parameters 71
- Data Rate Description 72
- Diagnostics 83
- Chapter 6 Diagnostics 85
- Receive Statistics 90
- Transmit Statistics 91
- Routine Procedures 93
- Ascertaining the ACU Version 94
- Selecting a Help Browser 95
- Loading New Firmware 95
- Uninstalling Manually 97
- Removing a PC Card 99
- Removing a PCI Client Adapter 99
- OL-1376-02 100
- Removing the Client Adapter 100
- Troubleshooting 101
- Using the Indicator LEDs 102
- Getting Help 104
- (Figure 8-3) 105
- Technical Specifications 107
- Power output 109
- Receiver sensitivity 109
- APPENDIX 113
- Channel Sets 114
- Translated Safety Warnings 117
- Warning for Laptop Users 119
- ¡Advertencia! 120
- Varning! 120
- Information 121
- Tested To Comply 122
- With FCC Standards 122
- FOR HOME OR OFFICE USE 122
- Canadian Compliance Statement 123
- Liechtenstein 124
- Japanese Translation 127
- English Translation 127
- GLOSSARY 129
- Glossary 130
- OL-1367-02 130
Produits connexes et manuels pour Mise en réseau Cisco Cisco Aironet Wireless LAN Client
(22 pages)
Mise en réseau Cisco MWR-1900-27 Spécifications
(448 pages)
(448 pages)
(4 pages)
Mise en réseau Cisco 7513 Spécifications
(24 pages)
(24 pages)
Mise en réseau Cisco Engine 611 Spécifications
(516 pages)
(516 pages)
(126 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.404 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels