Cisco Cisco Aironet Wireless LAN Client Spécifications Page 26
- Page / 142
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2-2
Cisco Aironet Wireless LAN Client Adapters Installation and Configuration Guide for Linux
OL-1376-02
Chapter 2 Preparing for Installation
Safety Information
Safety Information
Follow the guidelines in this section to ensure proper operation and safe use of the client adapter.
FCC Safety Compliance Statement
The FCC, with its action in ET Docket 96-8, has adopted a safety standard for human exposure to RF
electromagnetic energy emitted by FCC-certified equipment. Cisco Aironet products meet the
uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper operation of this
radio device according to the instructions in this publication will result in user exposure substantially
below the FCC recommended limits.
Safety Guidelines
• Do not touch or move the antenna while the unit is transmitting or receiving.
• Do not hold any component containing a radio such that the antenna is very close to or touching any
exposed parts of the body, especially the face or eyes, while transmitting.
• Do not operate the radio or attempt to transmit data unless the antenna is connected; otherwise, the
radio can be damaged.
• Use in specific environments:
–
The use of wireless devices in hazardous locations is limited to the constraints posed by the
safety directors of such environments.
–
The use of wireless devices on airplanes is governed by the Federal Aviation Administration
(FAA).
–
The use of wireless devices in hospitals is restricted to the limits set forth by each hospital.
• Antenna use:
–
To comply with FCC RF exposure limits, dipole antennas should be located at a minimum
distance of 7.9 inches (20 cm) or more from the body of all persons.
–
High-gain, wall-mount, or mast-mount antennas are designed to be professionally installed and
should be located at a minimum distance of 12 inches (30 cm) or more from the body of all
persons. Please contact your professional installer, VAR, or antenna manufacturer for proper
installation requirements.
Warnings
Observe the following warnings when operating the client adapter:
Warning
Do not operate your wireless network device near unshielded blasting caps or in an explosive
environment unless the device has been modified to be especially qualified for such use.
- Guide for Linux 1
- CONTENTS 3
- Contents 4
- 5 Advanced Configuration 5-1 5
- 6 Diagnostics 6-1 5
- 7 Routine Procedures 7-1 5
- 8 Troubleshooting 8-1 6
- Japanese Translation D-7 7
- English Translation D-7 7
- Audience 10
- Organization 10
- Conventions 11
- Attention 12
- Avvertenza 12
- Advarsel 12
- Related Publications 13
- Obtaining Documentation 13
- Ordering Documentation 14
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 15
- Cisco TAC Escalation Center 16
- Overview 17
- Terminology 18
- Parts of the Client Adapter 19
- Chapter 1 Overview 20
- Ad Hoc Wireless LAN 21
- Site Survey 22
- Preparing for Installation 25
- Safety Information 26
- Unpacking the Client Adapter 27
- System Requirements 27
- Site Requirements 28
- PCMCIA Installation 32
- Enter (Figure 3-3) 33
- Figure 3-7 Make All Screen 37
- Option 1 for Red Hat Systems 38
- Option 2 for Red Hat Systems 39
- Verifying Installation 41
- Inserting a PC Card 42
- Additional Procedures 44
- Opening the Client Utilities 46
- Selecting the Radio 47
- Enabling LEAP 52
- Using the Bcard Utility 53
- Finishing the Installation 54
- Enabling Security Features 55
- Server-Based Authentication 56
- Getting Started 56
- Changing the Password 56
- Entering a New WEP Key 57
- Selecting an Existing WEP Key 59
- Enabling WEP 59
- Message Integrity Check (MIC) 60
- Advanced Configuration 63
- Setting Enterprise Parameters 65
- Table 5-2 System Parameters 66
- Network Type Description 67
- Authentication Description 69
- Setting RF Network Parameters 71
- Data Rate Description 72
- Diagnostics 83
- Chapter 6 Diagnostics 85
- Receive Statistics 90
- Transmit Statistics 91
- Routine Procedures 93
- Ascertaining the ACU Version 94
- Selecting a Help Browser 95
- Loading New Firmware 95
- Uninstalling Manually 97
- Removing a PC Card 99
- Removing a PCI Client Adapter 99
- OL-1376-02 100
- Removing the Client Adapter 100
- Troubleshooting 101
- Using the Indicator LEDs 102
- Getting Help 104
- (Figure 8-3) 105
- Technical Specifications 107
- Power output 109
- Receiver sensitivity 109
- APPENDIX 113
- Channel Sets 114
- Translated Safety Warnings 117
- Warning for Laptop Users 119
- ¡Advertencia! 120
- Varning! 120
- Information 121
- Tested To Comply 122
- With FCC Standards 122
- FOR HOME OR OFFICE USE 122
- Canadian Compliance Statement 123
- Liechtenstein 124
- Japanese Translation 127
- English Translation 127
- GLOSSARY 129
- Glossary 130
- OL-1367-02 130
Produits connexes et manuels pour Mise en réseau Cisco Cisco Aironet Wireless LAN Client
(22 pages)
Mise en réseau Cisco MWR-1900-27 Spécifications
(448 pages)
(448 pages)
(4 pages)
Mise en réseau Cisco 7513 Spécifications
(24 pages)
(24 pages)
Mise en réseau Cisco Engine 611 Spécifications
(516 pages)
(516 pages)
(126 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.663 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels