Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Copyright © 2002 Cisco Systems, Inc. All rights reserved. Cisco, Cisco IOS, Cisco Systems, and
the Cisco Systems logo are registered trademarks of Cisco Systems, Inc. or its affiliates in the U.S.
and certain other countries. All other brands, names, or trademarks mentioned in this document
or Web site are the property of their respective owners. The use of the word partner does not
imply a partnership relationship between Cisco and any other company. (0201R)
Printed in the USA on recycled paper containing 10% postconsumer waste.
78-14624-02
Quick Start Guide
Installing a Cable Interface
Line Card in the
Cisco uBR10-LCP2 Adapter
Card
1 Overview
2 Feature Description
3 Installing the Line Card
4 Removing the Line Card
5 Troubleshooting
6 Technical Specifications
7 Related Documentation
Caution This is an ESD-sensitive product.
Make sure that you are properly
grounded before handling this
adapter card.
1 Overview
This quick start guide shows you how to install a
Cisco cable interface line card in the
Cisco uBR10-LCP2 adapter card (Figure 1).
Figure 1 Cisco uBR-LCP2 Adapter Card
Note This installation information applies to
both line card processor (LCP) adapter
card types, Cisco uBR10-LCP and
Cisco uBR10-LCP2.
2 Feature Description
The Cisco uBR10-LCP2 adapter card provides the
mechanical and electrical interfaces necessary for
cable interface line cards to fit the form factor used
in the Cisco uBR10012 chassis.
The adapter cards are identical except that the
Cisco uBR10-LCP2 has a faster CPU and faster
SDRAM access. Both adapter cards support N+1
requirements when they are used for redundancy
(protection).
The Cisco uBR10-LCP originally shipped with the
Cisco uBR10-LCP-MC16C/MC16E and
Cisco uBR10-LCP-MC28C cards. Both types (LCP
and LCP2) can be used in the same chassis, or the
Cisco uBR10-LCP can be replaced with the
Cisco uBR10-LCP2 adapter card, if needed.
72685
Ejector
Ejector
Ejector tab
Ejector tab
Guide
Guide
L-Bracket
nut and
washer
LCP2 connector
Backplane
connector
3 Installing the Line Card
Step 1 Verify that you are properly grounded.
Step 2 Place the Cisco uBR10-LCP2 adapter card
and the cable interface line card on a flat
antistatic surface or workbench.
Step 3 Remove the retaining nuts and washers
from the adapter card brackets. See
Figure 1.
Step 4 Align the line card with the guide rails on
the adapter card. Ensure that the bottom
of the line card is flush with the bottom of
the adapter card.
Step 5 Slowly slide the line card into the adapter
card. Make sure that the line card slides
under the spring guides and into the
guides. See Figure 2.
Figure 2 Installing the Cable Interface Card
Step 6 Verify that the connectors are aligned with
those on the adapter card.
Step 7 Make sure that the screws on the adapter
card brackets slide cleanly into the holes in
the L-brackets on the line card.
Note The brackets align the adapter
card and line card connectors and
hold the line card in place.
Step 8 Push on the front of the line card until the
connectors on the line card are firmly
seated in the connectors on the adapter
72683
US0
US1
US2
US3
US4
US5
DS
E
N
A
B
L
E
D
+
4
2
d
B
m
V
u
B
R
-
M
C
1
6
C
card. When the card is fully inserted, the
two ejector levers on the adapter card snap
into place.
Step 9 Tighten the captive screws on the line card
to secure it to the adapter card.
Step 10 Replace the retaining washers and nuts on
the L-brackets (Figure 3). Make sure that
the nuts are finger-tight, and then turn
them a half turn with a wrench to secure
the line card to the adapter card.
Figure 3 Replacing the Washers and Nut
Step 11 Install the combined adapter card and
cable interface line card in the
Cisco uBR10012 chassis.
For more information see Installing a
Cisco uBR10-LCP2-MCXX Cable
Interface Line Card Quick Start Guide.
US0
US1
US2
US3
US4
US5
DS
E
N
A
B
L
E
D
+
4
2
d
B
m
V
u
B
R
-
M
C
1
6
C
72682
Captive screw
Captive screw
(22 pages)
(448 pages)
(4 pages)
(126 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels