Cisco Cisco Aironet Wireless LAN Client Spécifications Page 41
- Page / 142
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3-13
Cisco Aironet Wireless LAN Client Adapters Installation and Configuration Guide for Linux
OL-1376-02
Chapter 3 Installing and Configuring the Client Adapter
Verifying Installation
Option 3 for Red Hat Systems
Option 3 is the most advanced installation method because it requires a complete kernel rebuild and
installation.
Caution You must use the kernel source in order to properly execute this procedure.
Note If you are not using a Red Hat system, version 7.1 or higher, but your distribution enables
PCMCIA support in the kernel by default, you need to disable it by following the instructions in
this section.
Step 1 To select option 3, type 3 and press Enter.
Step 2 Type cd /usr/src/linux-2.4.2 and press Enter.
Step 3 Type make menuconfig and press Enter.
Step 4 In the menuconfig window, scroll down to General setup and press Enter.
Step 5 Scroll down to PCMCIA/Cardbus support and press Enter.
Step 6 Continue to press the spacebar until the selector in front of the option is blank (does not contain an M
or an *).
Step 7 Continue to select Exit and press Enter until the following message appears:
“Do you wish to save your new kernel configuration?”
Step 8 Select Yes and press Enter.
Step 9 Rebuild your kernel.
Step 10 After the kernel is remade and reinstalled, reboot your computer.
Step 11 Go to Step 3 of the main upgrade procedure on page 3-4. This time select n when asked in Step 11 if you
are using a Red Hat system with an unmodified kernel.
Verifying Installation
To verify that you have properly installed the appropriate driver and client utilities, type
/opt/cisco/bin/acu & to open the ACU.
Note /opt/cisco/bin/ is the path where the ACU was installed.
If the installation was successful, the ACU main screen appears. Depending on how your wireless
network is configured, your client adapter might or might not associate to an access point. The fact that
you were able to launch the ACU verifies proper installation because it has found your client adapter’s
radio. You will need to configure the client adapter to communicate on your wireless network. See the
“Configuring Your Client Adapter” section on page 3-18 for instructions on how to initially configure
your client adapter.
- Guide for Linux 1
- CONTENTS 3
- Contents 4
- 5 Advanced Configuration 5-1 5
- 6 Diagnostics 6-1 5
- 7 Routine Procedures 7-1 5
- 8 Troubleshooting 8-1 6
- Japanese Translation D-7 7
- English Translation D-7 7
- Audience 10
- Organization 10
- Conventions 11
- Attention 12
- Avvertenza 12
- Advarsel 12
- Related Publications 13
- Obtaining Documentation 13
- Ordering Documentation 14
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 15
- Cisco TAC Escalation Center 16
- Overview 17
- Terminology 18
- Parts of the Client Adapter 19
- Chapter 1 Overview 20
- Ad Hoc Wireless LAN 21
- Site Survey 22
- Preparing for Installation 25
- Safety Information 26
- Unpacking the Client Adapter 27
- System Requirements 27
- Site Requirements 28
- PCMCIA Installation 32
- Enter (Figure 3-3) 33
- Figure 3-7 Make All Screen 37
- Option 1 for Red Hat Systems 38
- Option 2 for Red Hat Systems 39
- Verifying Installation 41
- Inserting a PC Card 42
- Additional Procedures 44
- Opening the Client Utilities 46
- Selecting the Radio 47
- Enabling LEAP 52
- Using the Bcard Utility 53
- Finishing the Installation 54
- Enabling Security Features 55
- Server-Based Authentication 56
- Getting Started 56
- Changing the Password 56
- Entering a New WEP Key 57
- Selecting an Existing WEP Key 59
- Enabling WEP 59
- Message Integrity Check (MIC) 60
- Advanced Configuration 63
- Setting Enterprise Parameters 65
- Table 5-2 System Parameters 66
- Network Type Description 67
- Authentication Description 69
- Setting RF Network Parameters 71
- Data Rate Description 72
- Diagnostics 83
- Chapter 6 Diagnostics 85
- Receive Statistics 90
- Transmit Statistics 91
- Routine Procedures 93
- Ascertaining the ACU Version 94
- Selecting a Help Browser 95
- Loading New Firmware 95
- Uninstalling Manually 97
- Removing a PC Card 99
- Removing a PCI Client Adapter 99
- OL-1376-02 100
- Removing the Client Adapter 100
- Troubleshooting 101
- Using the Indicator LEDs 102
- Getting Help 104
- (Figure 8-3) 105
- Technical Specifications 107
- Power output 109
- Receiver sensitivity 109
- APPENDIX 113
- Channel Sets 114
- Translated Safety Warnings 117
- Warning for Laptop Users 119
- ¡Advertencia! 120
- Varning! 120
- Information 121
- Tested To Comply 122
- With FCC Standards 122
- FOR HOME OR OFFICE USE 122
- Canadian Compliance Statement 123
- Liechtenstein 124
- Japanese Translation 127
- English Translation 127
- GLOSSARY 129
- Glossary 130
- OL-1367-02 130
Produits connexes et manuels pour Mise en réseau Cisco Cisco Aironet Wireless LAN Client
(22 pages)
Mise en réseau Cisco MWR-1900-27 Spécifications
(448 pages)
(448 pages)
(4 pages)
Mise en réseau Cisco 7513 Spécifications
(24 pages)
(24 pages)
Mise en réseau Cisco Engine 611 Spécifications
(516 pages)
(516 pages)
(126 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels