Cisco C8510-SRP - Switch Route Processor Guide de dépannage Page 187
- Page / 502
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
6-55
ATM and Layer 3 Switch Router Troubleshooting Guide
OL-1969-01
Chapter 6 Troubleshooting Switch Router ATM Network Connections
Troubleshooting Virtual Path Tunnel Connections
Step 7 Use the show atm pnni local-node command to check the node IDs and peer group IDs of higher-level
local nodes. If they are not based on the prefix of the ATM address, verify that no other peer group IDs
have been manually configured. Also, verify that the lowest-level node on the switch router has been
disabled and reenabled since the last time the active switch router ATM address was reconfigured.
Step 8 If an unexpected summary address appears in the list, use the show running-config command to make
sure that the summary address has not been manually configured.
If a summary prefix has been configured, but it is not possible to route to the summarized addresses from
another peer group, check for an overlapping summary address within the other peer group. If the
overlapping summary is for an automatically generated prefix, it could mean the ATM node addresses
need to be modified to give unique prefixes for the ancestors of the two peer groups.
Troubleshooting Virtual Path Tunnel Connections
This section describes how to troubleshoot virtual path (VP) tunnels. VP tunnels are used primarily
between private ATM networks across public ATM networks, such as telecom carriers, that do not yet
support ATM signalling. Signaling traffic is mapped into the VP tunnel and the switch routers that
allocate virtual channel connections (VCCs) on that VP instead of the default VP=0. With these
connections, signaling can travel transparently through the public network.
In the example network in Figure 6-5, the PVC tunnel connection configured between the switch router
on Floor 1 of the administration building and the switch router on Floor 1 of the remote sales building
has the following interface and subinterface numbers:
• AdminFl1ls1, ATM interface 1/0/0, PVP 99
• RsalFl1Ls1, ATM interface 4/0/0, PVP 99
Figure 6-5 VP Tunnel Test in the Example Network
This section contains the following procedures:
• Checking VP Tunnel Configuration
• Checking Virtual Path PVP Configuration
• Debugging VP Tunnel Connection Management
For detailed configuration information, see the “Configuring Interfaces” chapter in the
ATM Switch Router Software Configuration Guide.
Administration building
Remote sales
building
PVP
12118
(AdminFI1Ls1)
PVP IF = 1/0/0.99
ATM addr =
33.3333.3333.3333.3333.3333.3333.3333.3333.00
(RsalFl1Ls1)
PVP IF = 4/0/0.99
ATM addr =
44.4444.4444.4444.4444.4444.4444.4444.4444.00
Public ATM
network
- Cisco Reader Comment Card 1
- BUSINESS REPLY MAIL 2
- Troubleshooting Guide 3
- CONTENTS 5
- 3 Initial Troubleshooting 3-1 6
- 4 Example Network 4-1 6
- Contents 10
- OL-1969-01 10
- C ATM Cell Structures C-1 15
- D Creating a Core Dump D-1 15
- F Technical Support F-1 15
- Audience 17
- Organization 18
- Related Documentation 19
- Conventions 20
- Obtaining Documentation 21
- Cisco.com 22
- Technical Assistance Center 22
- Contacting TAC by Telephone 23
- Troubleshooting Overview 25
- Troubleshooting Tools 29
- Converted show epc Commands 30
- Using Diagnostic Commands 31
- • TDRs and OTDRs, page 2-5 32
- • Network Monitors, page 2-5 32
- • Network Analyzers, page 2-6 32
- TDRs and OTDRs 33
- Network Monitors 33
- Network Analyzers 34
- Initial Troubleshooting 35
- Accessibility Test 36
- OIR Test 36
- Snake Test 36
- Examples 37
- Using Bug Toolkit 39
- Checking IOS Release Notes 41
- Finding the Image 45
- IOS Upgrade Procedures 46
- Maintaining Functional Images 46
- Catalyst 8540 MSR) 48
- Example Network 55
- Example Networks 56
- Physical Connections 57
- Virtual Connections 58
- Chapter 4 Example Network 59
- Interface Connections 73
- Checking Cell Rates 75
- Performing OAM Loopback Tests 78
- OAM Loopback Testing 81
- Configuring Loopback Examples 82
- Line Coding Errors 89
- Interface Module LEDs 98
- OL-1969-02 103
- Port Adapter LEDs 104
- Interfaces 125
- • An AIS defect 131
- Network Connections 133
- Checking the UBR Resources 138
- • Packet discard 145
- • UPC option 145
- Checking UNI Interfaces 150
- Debugging SVC Signalling 153
- Alternate SVC Diagnostics 154
- Debugging PNNI SVC Routing 156
- Checking ATM Routes 157
- Checking PNNI Topology 158
- Checking SVC Downstream 159
- Hierarchical Network 160
- Checking SVCC-RCC Status 176
- Checking SVCC-RCC Hello State 177
- Checking Link Aggregation 183
- • Debugging Summary Addresses 184
- Debugging Summary Addresses 186
- Checking Traffic Priority 193
- Using PNNI Trace Connection 196
- Initiating a Trace Connection 197
- Environments 203
- Debugging the LANE Connection 211
- Troubleshooting Tag and MPLS 213
- Switching Connections 213
- How Tag Switching Works 214
- Troubleshooting TDP Neighbors 220
- MPLS Overview 224
- How MPLS Works 225
- MPLS Example 229
- Verifying CEF Switching 232
- Verifying MPLS 235
- Pinging Neighbors 236
- Verifying Label Distribution 236
- Verifying Label Bindings 237
- Troubleshooting MPLS VPN 238
- Verifying VRF Configurations 239
- Verifying Routing Information 240
- Verifying Labels 242
- Pinging ATM VPN Connections 254
- Debugging MPLS 256
- Network Clocking 257
- Performing Basic Checks 258
- CES Example Network 260
- Overview of Network Clocking 263
- Network Clock Module LEDs 264
- Layer 3 to Layer 3 269
- Connection Troubleshooting 269
- Uplink Interfaces 271
- • Detect port stuck failure 276
- 100BASE-FX Interface Modules 279
- Interface Modules 303
- Module LED Descriptions 304
- • SONET Tech Tips 311
- Descriptions 311
- Descriptions (continued) 312
- Defining Layer 3 Switching 320
- Understanding Packet Flow 320
- C8540CSR-1 321
- C8540CSR-2 321
- Layer 3 Forwarding 324
- Layer 2 Bridging 324
- Overview of Layer 3 Switching 325
- System Architecture 326
- Route Processor 327
- Routing Protocols 328
- Layer 2 VLAN and Switching 328
- Cisco Express Forwarding 329
- CEF Operation 330
- The Frame Scheduler 332
- Line Card Architecture 334
- CEFA Search Engine 335
- Fabric Interface 335
- Figure 11-13 Shared CAM 337
- Checking the IP Routing Table 345
- Checking the Interface Status 346
- CAM encoding: 354
- 0x009021DDDDDD 354
- • IP routing is on 355
- Layer 3 IP Multicast Overview 361
- Dense Mode 362
- Sparse Mode 362
- The Multicast Routing Table 364
- Utilization Problems 369
- Troubleshooting SDM Problems 374
- Layer 2 Switching 383
- Bridging 384
- Layer 2 Switching Broadcasts 385
- Layer 2 CAM Display 393
- Check for Spanning Tree Loop 393
- Before Configuring IRB 395
- • Load balancing 398
- • Fault tolerance 398
- Layer 3 to ATM 403
- Connections 405
- ATM Router Module Overview 406
- Hardware Restrictions 407
- ATM Router Module Software 408
- IPX Switching Overview 422
- • That the IP routing is on 436
- Appendixes 443
- Debugging a Switch Router 445
- Using the Debug Interface 446
- Using the debug ? Command 447
- Enabling Message Logging 450
- Passwords 455
- Cannot Compile Daemon 456
- Daemon Is Not Up and Running 457
- Daemon Does Not Run 457
- Recovering a Lost Password 459
- ATM Cell Structures 461
- Appendix 462
- OAM Cell Structure 463
- LANE Data Frame 465
- Creating a Core Dump 467
- Using the write core Command 469
- APPENDIX 471
- Line Coding 472
- Connection Alarm Types 473
- Architecture Problems 474
- Port Stuck Message 477
- Potential Causes 478
- Technical Support 481
- Numerics 485
Produits connexes et manuels pour Mise en réseau Cisco C8510-SRP - Switch Route Processor
Mise en réseau Cisco MC16E Spécifications
(19 pages)
(19 pages)
BORK SF NNN 3340 SI manuals
Owner’s manuals and user’s guides for Fans BORK SF NNN 3340 SI.
We providing 1 pdf manuals BORK SF NNN 3340 SI for download free by document types: User Manual
Commentaires sur ces manuels