Cisco AS5300 - Universal Access Server Spécifications Page 37
- Page / 50
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configure Voice over IP for Microsoft NetMeeting
Voice over IP for the Cisco AS5300 37
Configure CODEC for a VoIP Dial Peer
To specify a voice coder rate for a selected VoIP peer, use the following commands beginning in
global configuration mode:
The default for the codec command is g729r8; normally the default configuration for this command
is the most desirable. If, however, you are operating on a high bandwidth network and voice quality
is of the highest importance, you should configure the codec command for G711 A Law or
G711 U Law. Using either of these values will result in better voice quality, but it will also require
higher bandwidth requirements for voice.
For example, to specify a CODEC rate of G.711A Law for VoIP dial peer 108, enter the following:
dial-peer voice 108 voip
destination-pattern +1408528
codec g711alaw
session target ipv4:10.0.0.8
Configure VAD for a VoIP Dial Peer
To disable the transmission of silence packets for a selected VoIP peer, use the following commands
beginning in global configuration mode:
The default for the vad command is enabled; normally the default configuration for this command
is the most desirable. If you are operating on a high bandwidth network and voice quality is of the
highest importance, you should disable vad. Disabling VAD will result in better voice quality, but it
will also require higher bandwidth requirements for voice.
For example, to enable VAD for VoIP dial peer 108, enter the following:
dial-peer voice 108 voip
destination-pattern +1408528
vad
session target ipv4:10.0.0.8
Configure Voice over IP for Microsoft NetMeeting
Voice over IP can be used with Microsoft NetMeeting (Version 2.x) when the Cisco AS5300 is used
as the voice gateway. Use the latest version of DirectX drivers from Microsoft on your PC to improve
the voice quality of NetMeeting.
Step Command Purpose
1 dial-peer voice number voip Enters the dial peer configuration mode to
configure a VoIP peer.
2 codec [g711alaw | g711ulaw | g729r8] Specifies the desired voice coder rate of speech.
Step Command Purpose
1 dial-peer voice number voip Enters the dial peer configuration mode to
configure a VoIP peer.
2 vad Disables the transmission of silence packets
(enabling VAD).
- Feature Summary 1
- List of Terms 3
- Platforms 4
- Prerequisites 5
- Supported MIBs and RFCs 5
- Configuration Tasks 6
- • Slow links 10
- • Need to save bandwidth 10
- Configure Custom Queueing 11
- Configuration Tasks 12
- Cisco IOS Release 12.0(3)T 12
- Configure Voice Ports 14
- Verify ISDN PRI Configuration 15
- Configure E1 R2 Voice Ports 19
- Configure T1 CAS Voice Ports 21
- Supervisory: Line Side 22
- Supervisory: Trunk Side 22
- Informational: Line Side 22
- Informational: Trunk Side 22
- Configure Number Expansion 25
- Configure Dial Peers 27
- Configure POTS Peers 30
- Configure VoIP Peers 33
- Configure RSVP for Dial Peers 36
- VFC Management 38
- Determine the Number of VFCs 40
- Identify the VFC Mode 40
- Copy Flash Files to the VFC 41
- Unbundle VCWare 42
- Erase the VFC Flash Memory 44
- Configuration Examples 45
- Configuration Examples 46
Produits connexes et manuels pour Mise en réseau Cisco AS5300 - Universal Access Server
(22 pages)
Mise en réseau Cisco MWR-1900-27 Spécifications
(448 pages)
(448 pages)
(4 pages)
Mise en réseau Cisco 7513 Spécifications
(24 pages)
(24 pages)
Mise en réseau Cisco Engine 611 Spécifications
(516 pages)
(516 pages)
(126 pages)BORK SF NNN 3340 SI manuals
Owner’s manuals and user’s guides for Fans BORK SF NNN 3340 SI.
We providing 1 pdf manuals BORK SF NNN 3340 SI for download free by document types: User Manual
Commentaires sur ces manuels