Cisco 3600 - 24 Port Digital Modem Network Module Guide d'installation Page 33
- Page / 142
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Connecting Ethernet Network Modules to a Network 4-3
Connecting Ethernet Ports
AUI Connections
Use an Ethernet AUI cable to connect the AUI port on the 1-port or 4-port Ethernet network
module to an Ethernet transceiver. The female end of the AUI cable mates with the
slide-latch connector of the transceiver cable. Figure 4-3 shows a thin Ethernet transceiver
as an example, but you can use any type of Ethernet transceiver.
Figure 4-3 Connecting an Ethernet AUI Port to a Transceiver
If the transceiver cable has thumbscrew connectors, you can connect it directly to the AUI
port by replacing the AUI port slide latch with a jackscrew (provided in a separate bag).
10BaseT Connections
Use an Ethernet 10BaseT cable to connect a 10BaseT port on the 1-port or 4-port Ethernet
network module to a hub or other network device. Figure 4-4 shows the 10BaseT port on
an Ethernet network module connected to a hub.
EN
ACT
LINK
3
2
1
0
ETH 0ETH 3
ETHERNET
4E
ETH 2 ETH 1
H9255
Ethernet AUI port (DB-15)
(with jackscrews or slide-latch)
Ethernet AUI cable
(not supplied)
Ethernet
transceiver
BNC connector
To thin Ethernet network
To thin Ethernet network
- About This Guide 1
- Audience 2
- Organization 2
- Conventions 4
- Cisco Connection Online 6
- Ordering Documentation 7
- Overview of Cisco Network 9
- Slot Numbering 12
- DO NOT INSTALL WAN INTERFACE 13
- CARDS WITH POWER APPLIED 13
- Unit Numbering 14
- Cisco 2600 Series Routers 15
- Slot and Unit Numbering 17
- Preparing to Install Network 19
- Safety Warnings 20
- Required Tools and Equipment 22
- Installing Network Modules in 23
- Cisco Modular Routers 23
- Asynchronous network module 24
- Blank Network Module Panels 25
- WAN interface card 27
- Connecting Ethernet Network 31
- Connecting Ethernet Ports 32
- AUI Connections 33
- 10BaseT Connections 33
- Ethernet 10BaseT 34
- 10BaseT hub 34
- 10BaseT cable 34
- 1-Port Fast Ethernet Module 35
- 10/100 bTX 37
- FAST ETHERNET 37
- LEDs Enable 37
- Connecting Fast Ethernet PRI 39
- 10/100BaseT 40
- Connecting the PRI Ports 42
- CT1/PRI port (DB-15) 43
- CTRLR 1CTRLR 0 44
- CT1/PRI CSU 45
- • CE1/PRI-B Port on page 5-9 47
- • CE1/PRI-U Port on page 5-11 47
- Connectors) 48
- CE1/PRI-U Port 49
- Fast Ethernet PRI Module LEDs 50
- Connecting Serial Network 53
- Serial DTE or DCE Devices 54
- Signaling Standards Supported 54
- Distance Limitations 55
- Asynchronous Devices 56
- RJ-45 to DB-25 adapter 57
- Modem or terminal 57
- Slot 0Slot 1 Power supply 58
- 1 Cisco 3640 router only 59
- 4-Port Serial Network Module 62
- • V.35 Serial Cable Assembly 63
- • X.21 Serial Cable Assembly 63
- Serial port LEDs 65
- ASYNC 24-31 ASYNC 16-23 66
- ASYNC 8-15 66
- ASYNC 0-7 66
- Network Module 67
- LEDs shown in Table 6-7 70
- Connecting ISDN BRI Network 71
- BRI 3 BRI 2 BRI 1 BRI 0 73
- B1 B2 B1 B2 B1 B2 B1 B2 73
- BRI S/T Module LEDs 74
- BRI U ports (RJ-45) 76
- NT1 LEDs 77
- ISDN BRI LEDs 77
- BRI U Modules LEDs 78
- Connecting ISDN PRI Network 81
- CT1/PRI-U port (DB-15) 82
- CT1/PRI-U ports (DB-15) 83
- CT1/PRI Module LEDs 84
- Network Modules 85
- CT1/PRI CSU Module LEDs 87
- Table 8-2 88
- (120-ohm) Network Modules 89
- (DB-15-to-DB-15 Connectors) 91
- 1FE-1CE1-B/U 92
- CE1/PRI Module LEDs 93
- (75-ohm) Network Modules 94
- CSU with BNC connectors 95
- Connecting Voice Network 99
- Voice Network Module LEDs 101
- Connecting Digital 103
- Modem Network Modules to a 103
- Hardware Requirements 105
- Interface Numbering 106
- Figure 10-3.) 108
- Alignment holes 109
- Connector edge 109
- Removing 6-Port MICA Modules 111
- Digital Modem Module LEDs 118
- Connecting Analog Modem 119
- Network Modules to a Network 119
- 76543210 120
- 15 14 13 12 11 10 9 8 120
- Supported Network Protocols 121
- RJ-11 jack 124
- Analog modem port (RJ-11) 124
- Straight-through 124
- RJ-11 cable 124
- 76543210IN USE 125
- 15 14 13 12 11 10 9 8 IN USE 125
- Connecting ATM Network 127
- Modules to a Network 127
- RJ-45 port 128
- Enable LED 128
- ATM traffic 128
- ADSL modem 129
- RJ-45-to-RJ-45 cable 129
- ATM-25 port 129
- ATM-25 Network Module LEDs 130
- Connecting HSSI Network 131
- HSSI port LEDs 132
- HSSI port 132
- External DSU 133
- HSSI DTE cable 133
- HIGH SPEED SERIAL 133
- HSSI Network Module LEDs 134
- Connecting Compression 137
- Supported Interfaces 138
- COMPRESSION 139
- Error LED 139
- Active LED 139
- FCC Class B Compliance 141
Produits connexes et manuels pour Mise en réseau Cisco 3600 - 24 Port Digital Modem Network Module
(28 pages)
(44 pages)
(98 pages)
(48 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels