Cisco 3600 - 24 Port Digital Modem Network Module Guide d'installation Page 25
- Page / 142
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installing Network Modules in Cisco Modular Routers 3-3
Blank Network Module Panels
The following warning applies to routers that use a DC power supply:
Blank Network Module Panels
If the router is not fully configured with network modules, make sure that blank panels fill
the unoccupied chassis slots to provide proper airflow. (See Figure 3-2.)
Figure 3-2 Blank Network Module Panel
Installing a WAN Interface Card in a Network Module Slot
The following instructions apply only to installing a WAN interface card in a module slot.
To install a module in a chassis slot, see the “Installing a Network Module in a Modular
Router Chassis Slot” section on page 3-1. To see translated versions of the warnings that
appear in this chapter, see the Regulatory Compliance and Safety Information document
that accompanied the router.
Warning After wiring the DC power supply, remove the tape from the circuit breaker
switch handle and reinstate power by moving the handle of the circuit breaker to the ON
position.
Warning Only trained and qualified personnel should be allowed to install or replace this
equipment.
H6552
- About This Guide 1
- Audience 2
- Organization 2
- Conventions 4
- Cisco Connection Online 6
- Ordering Documentation 7
- Overview of Cisco Network 9
- Slot Numbering 12
- DO NOT INSTALL WAN INTERFACE 13
- CARDS WITH POWER APPLIED 13
- Unit Numbering 14
- Cisco 2600 Series Routers 15
- Slot and Unit Numbering 17
- Preparing to Install Network 19
- Safety Warnings 20
- Required Tools and Equipment 22
- Installing Network Modules in 23
- Cisco Modular Routers 23
- Asynchronous network module 24
- Blank Network Module Panels 25
- WAN interface card 27
- Connecting Ethernet Network 31
- Connecting Ethernet Ports 32
- AUI Connections 33
- 10BaseT Connections 33
- Ethernet 10BaseT 34
- 10BaseT hub 34
- 10BaseT cable 34
- 1-Port Fast Ethernet Module 35
- 10/100 bTX 37
- FAST ETHERNET 37
- LEDs Enable 37
- Connecting Fast Ethernet PRI 39
- 10/100BaseT 40
- Connecting the PRI Ports 42
- CT1/PRI port (DB-15) 43
- CTRLR 1CTRLR 0 44
- CT1/PRI CSU 45
- • CE1/PRI-B Port on page 5-9 47
- • CE1/PRI-U Port on page 5-11 47
- Connectors) 48
- CE1/PRI-U Port 49
- Fast Ethernet PRI Module LEDs 50
- Connecting Serial Network 53
- Serial DTE or DCE Devices 54
- Signaling Standards Supported 54
- Distance Limitations 55
- Asynchronous Devices 56
- RJ-45 to DB-25 adapter 57
- Modem or terminal 57
- Slot 0Slot 1 Power supply 58
- 1 Cisco 3640 router only 59
- 4-Port Serial Network Module 62
- • V.35 Serial Cable Assembly 63
- • X.21 Serial Cable Assembly 63
- Serial port LEDs 65
- ASYNC 24-31 ASYNC 16-23 66
- ASYNC 8-15 66
- ASYNC 0-7 66
- Network Module 67
- LEDs shown in Table 6-7 70
- Connecting ISDN BRI Network 71
- BRI 3 BRI 2 BRI 1 BRI 0 73
- B1 B2 B1 B2 B1 B2 B1 B2 73
- BRI S/T Module LEDs 74
- BRI U ports (RJ-45) 76
- NT1 LEDs 77
- ISDN BRI LEDs 77
- BRI U Modules LEDs 78
- Connecting ISDN PRI Network 81
- CT1/PRI-U port (DB-15) 82
- CT1/PRI-U ports (DB-15) 83
- CT1/PRI Module LEDs 84
- Network Modules 85
- CT1/PRI CSU Module LEDs 87
- Table 8-2 88
- (120-ohm) Network Modules 89
- (DB-15-to-DB-15 Connectors) 91
- 1FE-1CE1-B/U 92
- CE1/PRI Module LEDs 93
- (75-ohm) Network Modules 94
- CSU with BNC connectors 95
- Connecting Voice Network 99
- Voice Network Module LEDs 101
- Connecting Digital 103
- Modem Network Modules to a 103
- Hardware Requirements 105
- Interface Numbering 106
- Figure 10-3.) 108
- Alignment holes 109
- Connector edge 109
- Removing 6-Port MICA Modules 111
- Digital Modem Module LEDs 118
- Connecting Analog Modem 119
- Network Modules to a Network 119
- 76543210 120
- 15 14 13 12 11 10 9 8 120
- Supported Network Protocols 121
- RJ-11 jack 124
- Analog modem port (RJ-11) 124
- Straight-through 124
- RJ-11 cable 124
- 76543210IN USE 125
- 15 14 13 12 11 10 9 8 IN USE 125
- Connecting ATM Network 127
- Modules to a Network 127
- RJ-45 port 128
- Enable LED 128
- ATM traffic 128
- ADSL modem 129
- RJ-45-to-RJ-45 cable 129
- ATM-25 port 129
- ATM-25 Network Module LEDs 130
- Connecting HSSI Network 131
- HSSI port LEDs 132
- HSSI port 132
- External DSU 133
- HSSI DTE cable 133
- HIGH SPEED SERIAL 133
- HSSI Network Module LEDs 134
- Connecting Compression 137
- Supported Interfaces 138
- COMPRESSION 139
- Error LED 139
- Active LED 139
- FCC Class B Compliance 141
Produits connexes et manuels pour Mise en réseau Cisco 3600 - 24 Port Digital Modem Network Module
(28 pages)
(44 pages)
(98 pages)
(48 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels