Cisco 1600R Guide d'installation Page 43
- Page / 88
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Optional Installations 3-7
Connecting an ISDN Telephone to the Cisco 1604
Connecting an ISDN Telephone to the Cisco 1604
This section describes how to connect an ISDN telephone (or another ISDN device) to the
ISDN PHONE port on the rear panel of the Cisco 1604. The ISDN PHONE port is only for
connecting a second ISDN device. Routing cannot be performed over this port.
Note The router does not supply power to a device connected to the ISDN PHONE port.
Any device connected to the ISDN PHONE port must have its own internal or external
power supply.
Configuration Changes
When you are connecting a second ISDN device to the ISDN line through the router, you
need to use subaddressing on the ISDN line.
For more information about using subaddressing, refer to the “ISDN BRI Line
Configuration Requirements” section in the “Configuring the ISDN Line” appendix.
Before Installing the Telephone
This procedure in this section assumes that you have already connected the router
ISDN Ø U port to the ISDN wall-jack as described in the “Connecting the Cisco 1604 to
the WAN” section in the “Installing the Router” chapter earlier in this guide.
Installing the Telephone
This example procedure describes how to connect an AT&T ISDN telephone
(model ISDN 8510T) and an AT&T external power supply (model MSP-1) that supplies
power to this telephone. Depending on the model of telephone and power supply that you
are installing, the procedure for connecting the telephone and power supply could differ
slightly from the one shown in this section.
- About This Guide 1
- Installation Guide Overview 2
- Overview of the Router 5
- Router Features 6
- WAN Interface Cards 8
- Rear-Panel Connectors 8
- Overview of the Router 1-5 9
- ETHERNET Ø 10
- Router Memory 11
- Run-From-RAM Architecture 12
- • Amount of Flash memory 14
- Unpacking the Router 15
- Documentation 16
- Overview of the Router 1-13 17
- Installing the Router 19
- Installing the Router 2-3 21
- Connecting to an AUI Ethernet 22
- DO NOT INSTALL ANY WAN 23
- MODULE WITH POWER ON 23
- 10BaseT port 24
- 10BaseT link LED 24
- 10BaseT hub 24
- Straight-through 24
- Ethernet cable 24
- Cisco 1605 LAN Connections 25
- RJ-48S-to-RJ-48S cable 29
- Installing the Router 2-13 31
- Wall jack 32
- BRI cable 32
- RJ-45-to-RJ-45 cable 33
- Connecting the Console Port 34
- Installing the Router 2-17 35
- Optional Installations 37
- Safety Information 38
- WAN interface card 40
- Installing a Flash PC Card 41
- Configuration Changes 43
- Installing the Telephone 43
- H7204 44
- Wall-Mounting the Router 46
- Optional Installations 3-11 47
- Troubleshooting 49
- Router> show version 50
- Router> enable 52
- Router# show startup-config 52
- Router# configure terminal 52
- Problem Solving 53
- Troubleshooting ISDN 55
- Front Panel LEDs 59
- Rear Panel LEDs 62
- Cisco 1604 63
- Cisco 1605 63
- Configuring the ISDN Line 65
- ISDN BRI Switch Types 66
- North America 67
- New Zealand 67
- 5ESS Custom BRI For data only 67
- 5ESS National ISDN 68
- (NI-1) BRI 68
- DMS-100 BRI 68
- ISDN Configuration Options 70
- ISDN Configuration Options 72
- Hardware Specifications and 73
- Cable Pinouts 73
- Hardware Specifications 74
- Pin 1 on one connector and 77
Produits connexes et manuels pour Mise en réseau Cisco 1600R
(5 pages)
(23 pages)
(32 pages)Kenwood MFJ-286 manuels
Manuels d'utilisation et guides de l'utilisateur pour Microphones Kenwood MFJ-286.
Nous fournissons des manuels en pdf 1 Kenwood MFJ-286 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels