Cisco SPA8800 Manuel d'utilisateur télécharger pdf (Page 1)

Quick Start Guide

Cisco Small Business Pro

SPA8800 Phone Adapter with Router

Package Contents

• SPA8800 Analog Telephone Adapter with Router

• Power Adapter

• RJ-45 Ethernet Cable

• RJ-11 Phone Cables (4)

•Quick Start Guide

Before You Begin

The following basic services and equipment are required:

• An Integrated Access Device or modem for broadband access to the

Internet

• A computer with Microsoft Windows XP or Windows Vista for system

configuration

• An analog phone for administrative use with the Interactive Voice Response

(IVR) system

• (Recommended) An Uninterruptible Power Source (UPS), to ensure

continuous operation by providing continuous power to devices such as the

Integrated Access Device, switch, and router

Connect the Devices

NOTE If the SPA8800 is pre-configured by your ITSP, then you do

not need to change the default voice settings. Refer to the

documentation supplied by your service provider for more

information.

STEP 1 Power off your network devices, including your modem and PC.

TEP 2 Connect the phones to the SPA8800, by using one or both of the

following methods:

• Connect an RJ-21 connector to the RJ-21 port (A).

Connector Pinouts Circuit Pin (Ring) Pin (Tip)

FXS 1 1 26

FXS 2 2 27

FXS 3 3 28

FXS 4 4 29

FXO 1 17 42

FXO 2 18 43

• If you are connecting individual phone lines, connect one end of an

RJ-11 phone cable to the PHONE 1 port (B). Connect the other end

of the cable to an analog phone.

• Then connect other analog phones to the remaining PHONE ports

(C).

TEP 3 For access to the PSTN (Public Switched Telephone Network), connect

RJ-11 cables from the Line 1 to Line 4 FXO ports (D) to the RJ-11 wall

outlet for the telephone service.

FXO 3 19 44

FXO 4 20 45

Connector Pinouts Circuit Pin (Ring) Pin (Tip)

STEP 4 Connect one end of an Ethernet cable to the Ethernet port (E). Connect

the other end of the cable to your cable/DSL modem.

TEP 5 Connect an one end of an Ethernet network cable to the AUX port (F).

Connect the other end of the cable to the Ethernet port of your PC.

TEP 6 Connect the included power adapter to the power port (G). Insert the

power adapter into an electrical outlet. The power LEDs on the front

panel are lit.

TEP 7 Power on your PC. Make sure the Ethernet adapter of the PC is set to

obtain an IP address automatically. For more information, refer to

Windows Help.

Setting Up the Network

Connection

NOTE If the SPA8800 is pre-configured by your ITSP, then you do

not need to change the default voice settings. Refer to the

documentation supplied by your service provider for more

information.

STEP 1 Start a web browser on your PC. In the Address bar, enter the

following address: 192.168.0.1/advanced

TEP 2 If the login screen appears, enter the user name and password that

were supplied by your ITSP. If your ITSP did not supply a password,

you will not see a login screen.

TEP 3 When the Router - Status screen appears, click the WAN Setup tab.

1 2

Résumé du contenu

Page 1 - Connection

Quick Start GuideCisco Small Business Pro SPA8800 Phone Adapter with RouterPackage Contents• SPA8800 Analog Telephone Adapter with Router• Power Adapt

Page 2 - Where to Go from Here

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 40