Cisco SLM2008 - Small Business Smart Switch Informations techniques Page 94
- Page / 202
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Managing Device Diagnostics
Te s t i n g C o p p e r P o r t s
Cisco Small Business 200 Series Smart Switch Administration Guide 87
9
• Speed—Link speed.
• Link Status—Current link Up/Down status.
• Pair—Cable wire pairs being tested.
• Distance to Fault—Distance between the port and the location on the cable
where the fault was discovered.
• Status—Wire pair status. Red indicates fault and Green indicates status OK.
• Cable length—Cable length in meters.
If the link is down, TDR Technology is used to test the GE and FE ports. Cable
length measurements are accurate to within 3 to 4 meters.
If the link is up, DSP Technology is used to test the GE ports. (FE ports are not
tested for length.).
• Channel—Cable channel.
• Polarity—Indicates if automatic polarity detection and correction has been
activated for the wire pair.
• Pair Skew—Difference in delay between wire pairs.
STEP 5 Click Close to close the window.
- Cisco Small Business 1
- ADMINISTRATION 1
- Contents 2
- Chapter 1: Getting Started 1 2
- Chapter 5: System Time 55 3
- Getting Started 8
- Logging In 9
- Password Expiration 10
- Logging Out 10
- Login Page 11
- Application Header 12
- Management Buttons 14
- Viewing Statistics 16
- Viewing Etherlike Statistics 17
- Viewing 802.1X EAP Statistics 19
- Managing RMON Statistics 20
- Managing System Logs 23
- Setting System Log Settings 24
- Remote Log 25
- Servers Page 25
- Add Remote Log Server Page 25
- Remote Log Servers Page 25
- Viewing Memory Logs 26
- Flash Memory 27
- Managing System Files 28
- Language Files 34
- Copying Configuration Files 38
- DHCP Auto Configuration Page 39
- Auto Configuration Page 40
- System Time 41
- System Time Options 42
- Configuring System Time 43
- Adding an SNTP Server 45
- Add SNTP Server Page 46
- Defining SNTP Authentication 48
- Operations 49
- Security > TCP/UDP 50
- Services 50
- System Information 51
- Switch Models 52
- Rebooting the Switch 53
- Health Page 54
- Idle Session Timeout 54
- Pinging a Host 55
- Configuring Discovery 57
- Configuring LLDP 58
- Setting LLDP Properties 59
- Editing LLDP Port Settings 60
- LLDP Properties Page 61
- LLDP MED Protocol 62
- LLDP MED Network Policy Page 63
- LLDP MED Port Settings Page 64
- Displaying LLDP Port Status 65
- Local Information Page 67
- Neighbors Information Page 70
- Accessing LLDP Statistics 74
- LLDP Overloading 75
- Size (Bytes) 77
- Port Management 78
- Configuring Ports 80
- Configuring Link Aggregation 82
- Defining LAG Management 84
- Configuring LAG Settings 85
- Configuring LACP 86
- LACP Page 87
- Edit LACP Page 87
- Green Ethernet 88
- Managing Device Diagnostics 92
- Cable Extended Feature Page 93
- Optical Module Status Page 95
- Port and 96
- VLAN Mirroring Page 96
- Add Port/VLAN Mirroring 97
- Viewing CPU Utilization 98
- PoE on the Switch 99
- PoE Operation 100
- Configuring PoE Properties 101
- PoE Properties Page 102
- PoE Settings Page 103
- VLAN Management 105
- Default VLAN Settings 108
- Creating VLANs 109
- Interface Settings Page 110
- Defining VLAN Membership 112
- Configuring VLAN to Port 113
- Viewing VLAN Membership 114
- Voice VLAN 115
- Voice VLAN Options 116
- Voice VL AN 117
- Voice VLAN Properties Page 118
- Voice VLAN Properties 118
- Configuring Telephony OUI 119
- STP Flavors 120
- STP Status and 121
- Global Settings Page 121
- STEP 3 Enter the parameters 123
- Edit Rapid Spanning Tree Page 125
- Managing MAC Address Tables 128
- Dynamic MAC Addresses 129
- Querying Dynamic Addresses 130
- Multicast Forwarding 132
- Typical Multicast Setup 133
- Multicast Operation 133
- Multicast Registration 134
- Defining Multicast Properties 135
- STEP 2 Enter the parameters 136
- Adding MAC Group Address 137
- Add MAC Group Address 138
- Configuring IGMP Snooping 140
- IGMP Snooping Page 141
- Edit IGMP Snooping Page 141
- MLD Snooping 143
- MLD Snooping Page 144
- Edit MLD Snooping Page 144
- MAC Group Address Page 146
- Multicast Router Port Page 147
- Forward All Page 148
- Unregistered Multicast Page 149
- Configuring IP Information 151
- Management and IP Interfaces 152
- IP Addressing 153
- Defining an IPv4 Interface 153
- Administration 154
- File Management 154
- DHCP Auto Configuration 154
- Defining an IPv6 Interface 155
- Defining IPv6 Addresses 156
- Delay Time 158
- Configuring IPv6 Tunnels 159
- Modifying an IPv6 Neighbor 162
- Viewing IPv6 Route Tables 163
- Configuring ARP 164
- Domain Name Systems 165
- Defining DNS Servers 166
- Mapping DNS Hosts 167
- Configuring Security 169
- Defining Users 170
- Configuring RADIUS Parameters 172
- Defining Access Profiles 175
- STEP 5 Enter the parameters 177
- Defining Profile Rules 178
- STEP 4 Enter the parameters 179
- Configuring TCP/UDP Services 180
- Defining Storm Control 181
- Configuring Port Security 182
- Configuring 802.1X 184
- 802.1X Parameters Workflow 185
- Defining 802.1X Properties 186
- Viewing Authenticated Hosts 190
- QoS Features and Components 191
- Configuring QoS 192
- Configuring QoS Queues 194
- Queue Page 195
- CoS/802.1p to Queue Page 196
- Mapping DSCP to Queue 197
- Configuring Bandwidth 198
- Managing QoS Statistics 200
- , Cisco Stackpower 202
Produits connexes et manuels pour Logiciel Cisco SLM2008 - Small Business Smart Switch
Logiciel Cisco HWIC Guide d'installation
(82 pages)
(82 pages)
Logiciel Cisco Aironet 700 Series Spécifications
(402 pages)
(402 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels