Cisco IE 2000 Spécifications Page 103
- Page / 336
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
5-13
System Management Software Configuration Guide for Cisco IE 2000U and Connected Grid Switches
Chapter 5 Configuring the Switch Alarms
Configuration Example
Switch(config)# end
Switch(config)# show env alarm-contact
Switch# show env alarm-contact
ALARM CONTACT 1
Status: not asserted
Description: test_1
Severity: critical
Trigger: open
ALARM CONTACT 2
Status: not asserted
Description: door sensor
Severity: major
Trigger: closed
ALARM CONTACT 3
Status: not asserted
Description: flood sensor
Severity: critical
Trigger: closed
ALARM CONTACT 4
Status: not asserted
Description:
Severity: critical
Trigger: closed
This example sets the RPS monitoring alarm to the major relay:
Switch(config) # alarm facility power-supply rps relay major
This example shows how to set the FCS bit error rate for a port to 10
-10
:
Switch# configure terminal
Switch(config)# interface fastethernet1/1
Switch(config-if) # fcs-threshold 10
This example shows how to set the FCS error hysteresis at 5 percent:
Switch(config)# alarm facility fcs-hysteresis 5
This example creates or modifies the alarm profile fastE for the Fast Ethernet port with link-down
(alarmList ID 3) alarm enabled. The link-down alarm is connected to the major relay. This alarm also
send notifications to an SNMP server and sends system messages to a syslog server.
Switch(config)# alarm profile fastE
Switch(config-alarm-prof)# alarm 3
Switch(config-alarm-prof)# relay major 3
Switch(config-alarm-prof)# notifies 3
Switch(config-alarm-prof)# syslog 3
This example attaches an alarm profile named fastE to a port:
Switch(config)# interface fastethernet 1/2
Switch(config-if)# alarm profile fastE
This example detaches an alarm profile named fastE from a port:
Switch(config)# interface fastethernet 1/2
Switch(config-if)# no alarm profile fastE
- System Management Software 1
- CONTENTS 3
- 10 Configuring CDP 10-1 8
- 12 Configuring RMON 12-1 10
- 14 Configuring SNMP 14-1 11
- Contents 12
- A Supported MIBs A-1 14
- Overview 15
- Chapter 1 Overview 16
- Features 16
- Switch Boot Optimization 17
- MAC Address Table 17
- Switch Alarms 18
- SDM Templates 18
- Smartports Macros 18
- LLDP and LLDP-MED 19
- Port-Based Traffic Control 19
- SPAN and RSPAN 20
- System Message Logging 20
- Cisco IOS IP SLAs 21
- Embedded Event Manager 21
- Ethernet OAM, CFM, and E-LMI 22
- Online Diagnostics 22
- Supported MIBs 22
- Boot Process 24
- DHCP-Based Autoconfiguration 25
- DHCP Image Upgrade 26
- TFTP Server 27
- DNS Server 27
- Relay Device 28
- Obtaining Configuration Files 28
- Example Configuration 29
- Assigning Switch Information 33
- Configuring the Client 36
- Booting Manually 40
- First Reload 49
- Administering the Switch 53
- System Clock 54
- Network Time Protocol 54
- Configuring NTP 59
- Configuring NTP Associations 60
- Setting the System Clock 67
- Configuring DNS 72
- Creating a Banner 73
- Configuring a Login Banner 75
- MOTD Banner 88
- Configuring the Switch Alarms 91
- Port Status Monitoring Alarms 92
- Triggering Alarm Options 93
- Configuring External Alarms 94
- Configuring Switch Alarms 97
- Configuring Alarm Profiles 99
- BEFORE YOU BEGIN 100
- DETAILED STEPS 100
- Verifying Configuration 102
- Configuration Example 102
- Related Documents 104
- Feature History 104
- Configuring SDM Templates 105
- • Indirect IPv4 routes – 4 K 106
- Prerequisites 107
- Guidelines and Limitations 108
- Default Settings 108
- Configuring Smartports Macros 113
- Creating Smartports Macros 116
- Applying Smartports Macros 117
- Configuring LLDP and LLDP-MED 121
- LLDP-MED 122
- Disabling LLDP 125
- Enabling LLDP 125
- Configuring LLDP-MED TLVs 127
- Disabling a TLV 128
- Enabling a TLV 128
- Storm Control 134
- Protected Ports 135
- Port Blocking 135
- Port Security 135
- Secure MAC Addresses 136
- Security Violations 136
- Configuring Storm Control 140
- Configuring Protected Ports 142
- Configuring Port Blocking 143
- Configuring Port Security 144
- Configuring CDP 155
- Disabling and Enabling CDP 157
- Enabling CDP 158
- Disabling CDP on an Interface 158
- Enabling CDP on an Interface 159
- Configuring SPAN and RSPAN 163
- Local SPAN 164
- Remote SPAN 164
- SPAN Sessions 165
- Monitored Traffic 166
- Source Ports 167
- Source VLANs 168
- VLAN Filtering 168
- Destination Port 168
- RSPAN VLAN 169
- OL-29255-03 174
- Specifying VLANs to Filter 178
- Configuring RSPAN 179
- Configuring RMON 191
- System Log Message Format 200
- Disabling Message Logging 202
- Synchronizing Log Messages 204
- Verifying the Configuration 214
- Configuring SNMP 217
- SNMP Versions 218
- SNMP Manager Functions 219
- SNMP Agent Functions 220
- SNMP Community Strings 220
- SNMP Notifications 221
- Table 14-3 ifIndex Values 222
- Configuring Community Strings 225
- Event Detectors 244
- CFM Domain 260
- CFM Messages 263
- SNMP Traps and Fault Alarms 263
- Configuration Error List 263
- CFM Version Interoperability 264
- IP SLAs Support for CFM 264
- Configuring Ethernet CFM 265
- Configuring the CFM Domain 266
- Configuring Static Remote MEP 271
- Configuring a Port MEP 273
- Configuring SNMP Traps 275
- Configuring Fault Alarms 275
- Y.1731 Terminology 282
- Alarm Indication Signals 283
- Ethernet Locked Signal 284
- Multicast Ethernet Loopback 284
- Default Y.1731 Configuration 285
- Configuring ETH-AIS 285
- Configuring ETH-LCK 287
- Hold-time: 100 Minutes 292
- Configuring Ethernet OAM 293
- Enabling Ethernet Loopback 305
- Information About E-LMI 309
- Configuring E-LMI 310
- Configuring the OAM Manager 311
- Enabling E-LMI 314
- Enabling Ethernet OAM 319
- Scheduling Online Diagnostics 325
- Chapter A Supported MIBs 334
- MIB List 334
Produits connexes et manuels pour Logiciel Cisco IE 2000
Logiciel Cisco LRE CPE Spécifications
(648 pages)
(648 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels