Cisco 2950 - Catalyst Switch Spécifications Page 219
- Page / 674
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2-193
Catalyst 2950 and Catalyst 2955 Switch Command Reference
OL-10102-02
Chapter 2 Catalyst 2950 and 2955 Cisco IOS Commands
mac address-table static
Examples This example shows how to add the static address 0004.5600.67ab to the MAC address table:
Switch(config)# mac address-table static 0004.5600.67ab vlan 1 interface fastethernet0/2
This example shows how to add the static address c2f3.220a.12f4 to the MAC address table. When a
packet is received in VLAN 4 with this MAC address as its destination, the packet is forwarded to the
specified interface.
Switch(config)# mac address-table static c2f3.220a.12f4 vlan 4 interface
gigabitethernet0/1
You can verify your settings by entering the show mac address-table privileged EXEC command.
Related Commands Command Description
clear mac address-table Deletes entries from the MAC address table.
mac address-table aging-time Sets the length of time that a dynamic entry remains in the MAC
address table after the entry is used or updated.
show mac address-table Displays the MAC address table.
show mac address-table static Displays static MAC address table entries only.
- Command Reference 1
- CONTENTS 3
- Contents 10
- OL-10102-02 10
- B-10 12
- Audience 15
- Conventions 15
- Related Publications 16
- Type of Memory 19
- Platforms 19
- CLI Command Modes 20
- User EXEC Mode 21
- Privileged EXEC Mode 21
- Global Configuration Mode 22
- Interface Configuration Mode 22
- VLAN Configuration Mode 23
- Line Configuration Mode 23
- Command Summary 24
- Command Summary 26
- aaa authentication dot1x 30
- access-list (IP extended) 31
- access-list (IP standard) 34
- • The syntax for the FTP: 36
- • The syntax for the TFTP: 38
- archive tar 39
- archive upload-sw 42
- auto qos voip 44
- boot boothlpr 47
- boot buffersize 48
- boot config-file 49
- boot enable-break 50
- boot helper 51
- boot helper-config-file 52
- boot manual 53
- boot private-config-file 54
- boot system 55
- channel-group 56
- channel-protocol 60
- class 61
- class-map 63
- clear controllers lre log 69
- clear mac address-table 73
- clear vmps statistics 80
- Switch# clear vmps statistics 80
- clear vtp counters 81
- Switch# clear vtp counters 81
- cluster enable 85
- cluster management-vlan 87
- cluster member 88
- cluster run 90
- cpe toggle 103
- define interface-range 105
- delete 107
- Switch# delete flash:filename 107
- • Class of service (CoS) 112
- dot1x 114
- dot1x auth-fail vlan 116
- dot1x default 120
- dot1x guest-vlan 121
- dot1x initialize 124
- dot1x max-req 125
- dot1x multiple-hosts 126
- dot1x port-control 127
- dot1x re-authenticate 129
- dot1x re-authentication 130
- dot1x timeout 132
- duplex 134
- errdisable detect cause 136
- errdisable recovery 138
- flowcontrol 140
- hw-module slot 144
- (nonrouting) port 148
- interface port-channel 149
- interface range 150
- • fastethernet interface-id 151
- interleave 152
- ip access-group 154
- ip access-list 156
- ip dhcp snooping 159
- ip dhcp snooping trust 165
- ip dhcp snooping vlan 166
- ip igmp max-groups 168
- IGMP profile number 171
- ip igmp snooping 172
- ip ssh 185
- lacp port-priority 187
- lacp system-priority 189
- lre profile 200
- 1. Per-port sequence 201
- 2. Global sequence 201
- 3. Port profile 201
- 4. Global profile 201
- lre syslog 205
- Switch(config)# lre syslog 205
- lre upbo 206
- Switch# configure terminal 207
- Related Commands 207
- mac access-group 211
- mac access-list extended 213
- mac address-table static 218
- macro apply 222
- macro description 225
- macro global 226
- macro global description 228
- macro name 229
- margin 231
- match 233
- media-type 236
- mls qos cos 238
- mls qos map 239
- mls qos trust 242
- monitor session 245
- mvr immediate 251
- mvr type 253
- pagp learn-method 256
- pagp port-priority 258
- police 265
- policy-map 267
- port-channel load-balance 270
- rate selection 276
- rate selection sequence 279
- rcommand 280
- remote-span 283
- 0L-10102-02 289
- VLAN is configured: 343
- command to display an 465
- • 1000 Mbps—20000 478
- • 100 Mbps—200000 478
- • 10 Mbps—2000000 478
- Switch(config)# udld enable 541
- Switch# vmps reconfirm 563
- Switch(config)# vmps retry 7 564
- Catalyst 2955 Alarm Commands 581
- power-supply dual 590
- show alarm settings 595
- test relay 601
- Switch# test relay major on 601
- Boot Loader Commands 603
- boot 604
- • d—directory 609
- • r—readable 609
- • w—writable 609
- • x—executable 609
- flash_init 610
- format 611
- [-test 612
- help 613
- load_helper 614
- memory 616
- more 618
- rename 619
- rmdir 621
- type 625
- unset 626
- APPENDIX 629
- debug auto qos 631
- debug dot1x 632
- debug etherchannel 633
- debug lre 634
- debug pagp 635
- debug pm 636
- debug spanning-tree 638
- debug spanning-tree bpdu 641
- debug spanning-tree mstp 643
- debug switch dhcp 648
- debug sw-vlan 649
- debug sw-vlan ifs 651
- debug sw-vlan vtp 654
- debug udld 656
- Numerics 659
Produits connexes et manuels pour Logiciel Cisco 2950 - Catalyst Switch
Logiciel Cisco HWIC Guide d'installation
(82 pages)
(82 pages)
Logiciel Cisco Aironet 700 Series Spécifications
(402 pages)
(402 pages)
Logiciel Cisco 3130 Spécifications
(107 pages)
(107 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.108 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels