Cisco AS5300 - Universal Access Server Spécifications Page 171
- Page / 198
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Running Setup for Cisco IOS Release 11.3(2)T
Using Setup on Cisco IOS Releases 11.2 or 11.3(2)T C-11
Manufacture Cookie is not programmed.
1 Ethernet/IEEE 802.3 interface(s)
1 FastEthernet/IEEE 802.3 interface(s)
48 terminal line(s)
4 Channelized T1/PRI port(s)
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
4096K bytes of processor board Boot flash (Read/Write)
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Step 18 When the following message appears, press Enter to accept the default entry [yes] in
square brackets:
Would you like to enter the initial configuration dialog? [yes]:
Step 19 When the following message appears, press Enter to see the current interface summary:
First, would you like to see the current interface summary? [yes]:
Any interface listed with OK? value "NO" does not have a valid configuration
Interface IP-Address OK? Method Status Protocol
Ethernet0 unassigned NO unset up up
FastEthernet0 unassigned NO unset up
Step 20 Enter a host name for the access server:
Configuring global parameters:
Enter host name [Router]: 5300
The enable secret is a one-way cryptographic secret used
instead of the enable password when it exists.
Step 21 Enter an enable secret password. This password is encrypted (more secure) and cannot be
seen when viewing the configuration:
Enter enable secret: lab
The enable password is used when there is no enable secret
and when using older software and some boot images.
Step 22 Enter an enable password. This password is not encrypted (less secure) and can be seen
when viewing the configuration:
Enter enable password: guessme
Step 23 Enter the virtual terminal password, which is used for remote console access:
Enter virtual terminal password: guessagain
Step 24 Respond to the following prompts as appropriate for your network:
Configure SNMP Network Management? [yes]:
Community string [public]:
Configure LAT? [no]:
Configure AppleTalk? [no]: yes
Multizone networks? [no]: yes
Configure DECnet? [no]:
Configure IP? [yes]:
- Text Part Number: 78-4534-05 1
- CONTENTS 5
- Contents vii 7
- Appendix B ROM Monitor B-1 8
- Contents ix 9
- Book Title 10
- Document Objectives 11
- Changes to This Guide 11
- Document Organization 12
- Conventions 13
- Related Documentation 15
- Cisco Connection Online 15
- First-Time Configuration 17
- Universal access 18
- First-Time Configuration 1-3 19
- Getting Started 19
- First-Time Configuration 1-9 25
- Using the Setup Script 26
- Using Cisco IOS Software 29
- Understanding Command Modes 30
- How to Find Command Options 30
- Undoing a Command or Feature 32
- Saving Configuration Changes 32
- Using Cisco IOS Software 2-5 33
- Basic Configuration 35
- Configure 36
- Configuring Alarms 37
- Configuring Ethernet 10BaseT 38
- Configuring Ethernet 100BaseT 39
- Basic Configuration 3-9 43
- Configuring ISDN PRI 45
- Basic Configuration 3-15 49
- Configuring E1 R2 Signaling 50
- Basic Configuration 3-19 53
- If you are having trouble: 56
- Basic Configuration 3-23 57
- Basic Configuration 3-25 59
- Configuring the Modems 62
- Country Code Tables 63
- Basic Configuration 3-31 65
- Configuring Modem Pooling 67
- Configuring T1 CAS for VoIP 75
- Basic Configuration 3-43 77
- Configuring RLM 80
- Basic Configuration 3-47 81
- Configuring IPX Networks 84
- Basic Configuration 3-51 85
- Configuring AppleTalk 86
- Basic Configuration 3-53 87
- Configuring MMP 89
- Basic Configuration 3-57 91
- Configuring VPDN 92
- Basic Configuration 3-59 93
- Using Continuity Test (COT) 94
- Basic Configuration 3-61 95
- Basic Configuration 3-65 99
- Basic Configuration 3-67 101
- Basic Configuration 3-69 103
- Basic Configuration 3-71 105
- Where to Go Next 106
- Access Service Security 107
- Assumptions 108
- Remote Security Database 109
- Configuring Authentication 110
- Access Service Security 4-9 115
- 5300# configure terminal 116
- 5300(config)# aaa new-model 116
- Identify a List Name 117
- Access Service Security 4-13 119
- ARA Authentication Examples 122
- PPP Authentication Examples 122
- Configuring Authorization 123
- Authorization Examples 124
- Security Examples 125
- Managing Modems 127
- Monitoring Modems 128
- Ctrl-Shift-6 X 130
- 5300# disconnect 130
- to end the Telnet 130
- Polling Modems 132
- Troubleshooting Modems 133
- Upgrading Modem Code 135
- SPE Firmware bundled 137
- Using an Internet Browser 141
- Using an FTP Application 141
- • Upgrading MICA Modem Code 144
- Managing Modems A-19 145
- Upgrading Microcom Modem Code 146
- • Click OK 148
- • Bits per second: 9600 149
- • Data bits: 8 149
- • Parity: None 149
- • Stop bits: 1 149
- • Flow control: None 149
- ROM Monitor 153
- Command Aliasing 154
- ROM Monitor Commands 154
- ROM Monitor B-3 155
- ROM Monitor B-5 157
- ROM Monitor B-7 159
- Using Setup on 161
- Upgrade VoIP Software 185
- New Hardware Features 191
Produits connexes et manuels pour Serveurs Cisco AS5300 - Universal Access Server
Serveurs Cisco 7008 Manuel d'utilisateur
(9 pages)
(9 pages)
Serveurs Cisco 32369 Manuel d'utilisateur
(52 pages)
(52 pages)
Serveurs Cisco AS5800 Guide d'installation
(34 pages)
(34 pages)
Serveurs Cisco UCS B22 M3 Guide de dépannage
(34 pages)
(34 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels