Cisco Router IOS XR Spécifications Page 348
- Page / 446
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Implementing RIP on Cisco IOS XR Software
Additional References
RC-334
Cisco IOS XR Routing Configuration Guide
route-policy infil
if destination in pf2 then
add rip-metric 2
pass
endif
end-policy
!
router rip
interface GigabitEthernet0/6/0/0
route-policy policy_in in
!
interface GigabitEthernet0/6/0/2
!
route-policy infil in
route-policy pass-all out
Configuring Passive Interfaces and Explicit Neighbors for RIP: Example
The following example shows how to configure passive interfaces and explicit neighbors. When an
interface is passive, it only accepts routing updates. In other words, no updates are sent out of an
interface except to neighbors configured explicitly.
router rip
interface GigabitEthernet0/6/0/0
passive-interface
!
interface GigabitEthernet0/6/0/2
!
neighbor 172.17.0.1
neighbor 172.18.0.5
!
Controlling RIP Routes: Example
The following example shows how to use the distance command to install RIP routes in the Routing
Information Base (RIB). The maximum-paths command controls the number of maximum paths
allowed per RIP route.
router rip
interface GigabitEthernet0/6/0/0
route-policy polin in
!
distance 110
maximum-paths 8
!
Additional References
The following sections provide references related to implementing RIP on Cisco IOS XR software.
- Text Part Number: OL-12285-01 1
- CONTENTS 3
- Contents 10
- Preface 13
- Release Modification 15
- BGP Functional Overview 17
- BGP Router Identifier 18
- BGP Default Limits 18
- BGP Next Hop Tracking 19
- Scoped IPv4/VPNv4 Table Walk 20
- BGP Configuration 21
- Configuration Modes 22
- Neighbor Submode 23
- Configuration Templates 24
- Template Inheritance Rules 25
- Template Inheritance 29
- No Default Address Family 33
- Routing Policy Enforcement 34
- Table Policy 35
- Update Groups 36
- BGP Cost Community 36
- BGP Best Path Algorithm 41
- Order of Comparisons 43
- Best Path Change Suppression 43
- Administrative Distance 44
- Figure 3 Back Door Example 45
- Multiprotocol BGP 46
- Route Dampening 47
- BGP Route Reflectors 48
- Distributed BGP 51
- BGP Keychains 53
- IPv6 Provider Edge Multipath 54
- IP L3VPN w/L2TPv3 55
- Service Provider 56
- Enabling BGP Routing 58
- Logging Neighbor Changes 63
- Adjusting BGP Timers 64
- Configuring BGP Weights 68
- 5. router bgp as-number 99
- DETAILED STEPS 100
- Example: 101
- SUMMARY STEPS 103
- Configuring Distributed BGP 105
- BGP Load Balancing 121
- Redistribution of IGPs to BGP 123
- Configuring Keychains for BGP 126
- Disabling a BGP Neighbor 130
- Monitoring BGP Update Groups 138
- Software 139
- BGP Confederation: Example 142
- BGP Route Reflector: Example 143
- Where to Go Next 144
- Additional References 145
- Technical Assistance 146
- EIGRP Functional Overview 149
- EIGRP Features 149
- EIGRP Components 150
- EIGRP Configuration Grouping 151
- EIGRP Configuration Modes 151
- EIGRP Interfaces 152
- Mismatched K Values 153
- The Goodbye Message 154
- 10.1.1.0/24 157
- Enabling EIGRP Routing 160
- Restrictions 162
- /length 164
- Monitoring EIGRP Routing 174
- Cisco IOS XR Software 177
- IS-IS Functional Overview 183
- IS-IS Configuration Grouping 184
- IS-IS Configuration Modes 184
- IS-IS Interfaces 185
- Multitopology Configuration 185
- Limit LSP Flooding 186
- Single-Topology IPv6 Support 187
- Multitopology IPv6 Support 187
- IS-IS Authentication 187
- Nonstop Forwarding 188
- Multi-Instance IS-IS 189
- Overload Bit on Router 189
- Default Routes 190
- IS-IS Support for Route Tags 190
- Multicast-Intact Feature 190
- MPLS TE Forwarding Adjacency 192
- MPLS TE Interarea Tunnels 193
- IP Fast Reroute 193
- Prerequisites 194
- Prerequisite 211
- Tuning Adjacencies for IS-IS 214
- Customizing Routes for IS-IS 219
- Enabling Multicast-Intact 224
- OSPF Routing Components 240
- Autonomous Systems 241
- Stub Area 242
- Not-so-Stubby Area 242
- Area Border Routers 242
- OSPF Process and Router ID 243
- Supported OSPF Network Types 243
- Plain Text Authentication 244
- MD5 Authentication 244
- Authentication Strategies 244
- Key Rollover 244
- Default Route for OSPF 245
- Route Redistribution for OSPF 248
- Graceful Restart for OSPFv3 250
- Helper Mode 251
- • draft-ietf-ospf-cap-09 255
- Enabling OSPF 256
- area-id 257
- seconds 270
- Examples 275
- DETAILED STEP 290
- Summary Steps 292
- ABR 1 Configuration 314
- ABR 2 Configuration 314
- Standards 316
- RIB Administrative Distance 319
- RIB Support for IPv4 and IPv6 320
- RIB Statistics 320
- RIB Quarantining 321
- How to Deploy and Monitor RIB 322
- Related Documents 329
- RIP Functional Overview 332
- Split Horizon for RIP 333
- Route Timers for RIP 333
- Route Redistribution for RIP 334
- Enabling RIP 336
- Customize RIP 337
- Control Routing Information 340
- Named Set Form 355
- Inline Set Form 355
- Routing Policy Language Usage 359
- Set community based on MED 360
- Persistent Remarks 360
- Policy Definitions 361
- Parameterization 362
- Global Parameterization 363
- Boolean Operator Precedence 364
- When Attributes Are Modified 365
- Default Drop Disposition 365
- Control Flow 366
- Policy Verification 366
- Attached Policy Modification 367
- Policy Statements 368
- Boolean Conditions 371
- Attach Points 372
- BGP Policy Attach Points 373
- Dampening 374
- Default Originate 375
- Neighbor Export 375
- Neighbor Import 376
- Redistribute 377
- Show BGP 377
- Retain Route-Target 380
- Allocate-Label 381
- Neighbor-ORF 381
- Next-hop 382
- Clear-Policy 382
- BGP Attributes and Operators 383
- OSPF Policy Attach Points 393
- Area-out 394
- OSPF Attributes and Operators 394
- OSPFv3 Policy Attach Points 395
- IS-IS Policy Attach Points 396
- Default-Information Originate 397
- Inter-area-propagate 397
- EIGRP Policy Attach Points 398
- Default-Accept-In 399
- Default-Accept-Out 399
- Policy-In 399
- Policy-Out 400
- If-Policy-In 400
- If-Policy-Out 400
- RIP Policy Attach Points 401
- Global-Inbound 402
- Global-Outbound 402
- Interface-Inbound 403
- Interface-Outbound 403
- RIP Attributes and Operators 403
- • Nano (default) 405
- Defining a Route Policy 407
- policy-name 410
- Directly Connected Routes 419
- Recursive Static Routes 420
- Floating Static Routes 421
- Default VRF 421
- Configuring a Static Route 422
- Configuration Examples 430
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Cisco Router IOS XR
(504 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels