Cisco WS-X6416-GE-MT - Interface Module - Expansion Guide d'installation Page 171
- Page / 194
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
B-9
Catalyst 6500 Series Switch Module Installation Guide
78-15725-02
Appendix B Cable and Connector Specifications
Supervisor Engine Console Port Signals and Pinouts
CONSOLE PORT MODE Switch
Note Use a ballpoint pen tip or other small, pointed object to access the CONSOLE
PORT MODE switch. The switch is shipped in the in position.
The supervisor engine front-panel CONSOLE PORT MODE switch allows you to
connect a terminal or modem to the console port as follows:
• Mode 1—Switch in the in position. Use this mode to connect a terminal to the
console port using the RJ-45-to-RJ-45 rollover cable and DTE adapter
(labeled “Terminal”).
You can also use this mode to connect a modem to the console port using the
RJ-45-to-RJ-45 rollover cable and DCE adapter (labeled “Modem”).
See the “Console Port Mode 1 Signaling and Pinouts” section on page B-10.
• Mode 2—Switch in the out position. Use this mode to connect a terminal to
the console port using the Catalyst 5000 family Supervisor Engine III console
cable and appropriate adapter for the terminal connection (cable and adapter
are not provided).
See the “Console Port Mode 2 Signaling and Pinouts” section on page B-13.
Identifying a Rollover Cable
You can identify a rollover cable by comparing the two ends of the cable. Holding
the cables side-by-side, with the tab at the back, the wire connected to the pin on
the outside of the left plug should be the same color as the wire connected to the
pin on the outside of the right plug. (See Figure B-5.) If your cable was purchased
from Cisco Systems, pin 1 will be white on one connector, and pin 8 will be white
on the other (a rollover cable reverses pins 1 and 8, 2 and 7, 3 and 6, and 4 and 5).
- Installation Guide 1
- CONTENTS 5
- 3 Installing the Module 3-1 9
- Contents 10
- 78-15725-02 10
- Audience 11
- Organization 12
- Conventions 12
- Waarschuwing 14
- Varoitus 14
- Attention 15
- Avvertenza 15
- Advarsel 16
- ¡Advertencia! 16
- Varning! 17
- Related Documentation 19
- Obtaining Documentation 19
- Cisco.com 20
- Documentation CD-ROM 20
- Ordering Documentation 20
- Documentation Feedback 21
- Cisco TAC Website 22
- Opening a TAC Case 22
- TAC Case Priority Definitions 23
- Product Overview 25
- Catalyst 6000 Series Switches 26
- Catalyst 6500 Series Switches 28
- Supervisor Engines 32
- RESET Button 37
- CONSOLE Port 37
- Switch Load 39
- PCMCIA Slot 39
- Uplink Ports 39
- (WS-X6024-10FL-MT) 44
- (WS-X6148-GE-TX) 45
- (WS-X6148V-GE-TX) 45
- (WS-X6148-RJ21V) 46
- (WS-X6148-RJ45V) 47
- (WS-X6224-100FX-MT) 48
- (WS-X6248-RJ45) 49
- (WS-X6248-TEL) 49
- (WS-X6248A-TEL) 50
- (WS-X6324-100FX-MM) 50
- (WS-X6324-100FX-SM) 51
- (WS-X6348-RJ21V) 52
- (WS-X6348-RJ-45) 53
- (WS-X6348-RJ45V) 54
- (WS-X6524-100FX-MM) 55
- (WS-X6548-GE-TX) 55
- (WS-X6548V-GE-TX) 56
- Module (WS-X6548-RJ-21) 57
- Module (WS-X6548-RJ-45) 58
- Module (WS-X6748-GE-TX) 59
- 1000BASE-X GBIC ports 63
- Installed 66
- (WS-X6516-GE-TX) 68
- Ethernet Module LEDs 71
- ATM Modules 72
- ATM Module LEDs 75
- FlexWAN Module (WS-X6182-2PA) 76
- WAN Port Adapters 77
- STATUS LED 78
- Console port 80
- CONSOLE PORT 80
- MODE switch 80
- Network Analysis Modules 82
- • Netflow Data Export (NDE) 83
- SHUTDOWN 84
- SHUTDOWN button 84
- (WS-SVC-IPSEC-1) 90
- • The module is disabled 92
- STATUS LED PCMCIA slot 93
- SHUTDOWN button Hard drive 93
- (HD) LED 93
- RJ-45 (Test) 95
- Switch Fabric Modules 96
- ACTIVE LED 97
- 2 Line X 20 character 97
- LCD display 97
- Interface Module slots 100
- with CRC 101
- RJ-45 connectors 103
- Receive port LEDs 103
- Voice-Related Modules 104
- Statement 1031 106
- WS-X6624-FXS 107
- 24 PORT FXS ANALOG STATION 107
- Port Addresses 108
- Physical Interface Addresses 109
- MAC Addresses 110
- Switching Modules 111
- Preparing for Installation 113
- Determining Cable Distances 114
- Ethernet and Fast Ethernet 116
- Gigabit Ethernet 117
- 10-Gigabit Ethernet 119
- Patch Cord 121
- Patch Cord Installation 122
- Differential Mode Delay 123
- LED transmission 124
- Laser transmission 124
- RJ-45 (both ends) 127
- Port Densities 128
- Gigabit Interface Converters 130
- WS-G5483 Copper GBIC 131
- WS-G5487) 132
- Figure 2-11 CWDM GBIC 133
- Table 2-13 CWDM GBICs 133
- 1000BASE-T SFP Modules 135
- M-SFP-1470-2G 137
- Class 1 21CFR1040.10 137
- LN#50 7/01 03-13 137
- S/N: OH1233456 137
- Software Requirements 138
- Installing the Module 139
- Required Tools 140
- Statement 1051 141
- Horizontal slots 144
- Chapter 1 145
- Vertical slots 146
- All ejector levers flush 150
- Connecting a Terminal 153
- Connecting a Modem 154
- Using Flash PC Cards 155
- Verifying the Installation 157
- Connectivity 160
- Technical Specifications 161
- APPENDIX 163
- RJ-21 Connector 164
- RJ-21 (WS-X6624-FXS Only) 166
- RJ-45 Connector 167
- CONSOLE PORT MODE Switch 171
- Identifying a Rollover Cable 171
- Pin 1 and pin 8 172
- (DB-25 Adapter) 173
- Modem Adapter 174
- (Modem Adapter) 175
- Fiber-Optic Connectors 176
- MT-RJ Connectors 177
- LC Connectors 178
- Numerics 181
Produits connexes et manuels pour Mise en réseau Cisco WS-X6416-GE-MT - Interface Module - Expansion
(68 pages)
(38 pages)Kenwood MFJ-286 manuels
Manuels d'utilisation et guides de l'utilisateur pour Microphones Kenwood MFJ-286.
Nous fournissons des manuels en pdf 1 Kenwood MFJ-286 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels