Cisco WPC54GS Guide de l'utilisateur Page 31
- Page / 83
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
25
Chapter 5: Configuring the Dual-Band Wireless A+G Broadband Router
The Wireless Tab - Advanced Wireless Settings
Dual-Band Wireless A+G Broadband Router
Router’s ability to catch all Wireless-G transmissions but will severely decrease performance. If you do not want
to use CTS Protection Mode at all, select Disabled.
Frame Burst Mode. Enabling this option should provide your network with greater performance, depending on
the manufacturer of your wireless products. If you are not sure how to use this option, keep the default, Enabled.
Beacon Interval. The default value is 100. The Beacon Interval value indicates the frequency interval of the
beacon. A beacon is a packet broadcast by the Router to synchronize the wireless network.
DTIM Interval. This value indicates the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is
a countdown field informing clients of the next window for listening to broadcast and multicast messages. When
the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a
DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages.
The default value is 1.
Fragmentation Threshold. This value specifies the maximum size for a packet before data is fragmented into
multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation
Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor
reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.
RTS Threshold. Should you encounter inconsistent data flow, only minor reduction of the default value, 2347, is
recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will
not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates
the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS)
frame to acknowledge the right to begin transmission. The RTS Threshold value should remain at its default value
of 2347.
Change these settings as described here and click the Save Settings button to apply your changes or Cancel
Changes to cancel your changes. Help information is shown on the right-hand side of the screen. For additional
information, click More.
- Wireless A+G 1
- Copyright and Trademarks 2
- How to Use This User Guide 2
- Table of Contents 3
- List of Figures 5
- Chapter 1: Introduction 7
- What’s in this Guide? 8
- Network Topology 10
- Network Layout 10
- Broadband Router 12
- The Front Panel 13
- The Setup Tab - Basic Setup 19
- Optional Settings 20
- Network Setup 21
- Time Settings 22
- MAC Address Clone 23
- Wireless Network 24
- Wireless Security 26
- Wireless-G Settings 27
- Wireless MAC Filter 28
- Advanced Wireless 29
- The Security Tab - Firewall 32
- Internet Access Policy 33
- Port Range Forwarding 35
- Port Range Triggering 37
- Qos (Quality of Service) 39
- MAC Address Priority 40
- LAN Port Priority 40
- Management 42
- Backup and Restore 43
- The Administration Tab - Log 44
- Diagnostics 45
- Factory Defaults 46
- Firmware Upgrade 46
- The Status Tab - Router 47
- Local Network 48
- DHCP Server 48
- The Status Tab - Wireless 49
- Appendix A: Troubleshooting 50
- Common Problems and Solutions 51
- Frequently Asked Questions 58
- Appendix B: Wireless Security 65
- Appendix D: Windows Help 69
- Ethernet Adapter 70
- Appendix F: Glossary 72
- Appendix G: Specifications 79
Produits connexes et manuels pour Mise en réseau Cisco WPC54GS
Mise en réseau Cisco ME 3800X Spécifications
(622 pages)
(622 pages)
Kenwood MFJ-286 manuels
Manuels d'utilisation et guides de l'utilisateur pour Microphones Kenwood MFJ-286.
Nous fournissons des manuels en pdf 1 Kenwood MFJ-286 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels