Cisco 6260 Guide d'installation Page 50
- Page / 244
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1-32
Cisco 6260 Hardware Installation Guide
OL-2365-02
Chapter 1 Product Overview
Cisco 6260 System Overview
Table 1-10 describes the LED group indicators and their functions.
1.2.3.10 DS3+T1/E1 IMA NI-2 Card Overview
The DS3+T1/E1 IMA NI-2 card
• Provides the following network trunk and subtend interfaces:
1. TRNK = trunk
2. SBTD = subtend
Table 1-10 DS3/2DS3 NI-2 Card LED Group Indicators
LED Group LED State Function
Interface
status LED
(5 in
Figure 1-16)
TEST Amber solid Cisco IOS detects that an obtrusive test (loopback) is
active on this interface.
Off Cisco IOS does not detect obtrusive test activity.
RX
1
STAT
1. RX = receive
Amber solid The receiver detects a physical layer problem.
Off The receiver does not detect a physical layer problem.
TX
2
STAT
2. TX = transmit
Amber solid The transmitter detects a physical layer problem.
Off The transmitter does not detect a physical layer
problem.
RCLK
3
3. RCLK = receive clock
Green solid Hardware detects an incoming clock signal.
Off Hardware does not detect an incoming clock signal.
System alarm
(6 in
Figure 1-16)
CRITICAL Red A critical alarm is active.
MAJOR Red A major alarm is active.
MINOR Amber A minor alarm is active.
Card status
(7 in
Figure 1-16)
POWER Green The NI-2 card has power.
STATUS Green The operational status of the NI-2 card.
• On—There are no internal faults or problems.
• Off—The NI-2 card has not booted properly, or a
problem is preventing normal operation.
ACTIVE Green The NI-2 card is operating as the active NI-2 card in
the chassis.
Fan alarm
(8 in
Figure 1-16)
FAN 1 Red The fan module or fan tray is not operational and is in
alarm mode.
FAN 2 Off The fan tray is off.
ENET
interface LED
(11 in
Figure 1-16)
ACT Green solid or
blinking
The Ethernet interface is active.
Off The Ethernet interface is inactive.
LNK Green solid The Ethernet link is connected and enabled.
- Text Part Number: OL-2365-02 1
- CONTENTS 3
- Contents 4
- 5 Troubleshooting 5-1 6
- OL-2365-02 10
- Audience 13
- Organization 13
- Conventions 14
- Related Documentation 15
- Obtaining Documentation 16
- Cisco.com 17
- Technical Assistance Center 17
- Contacting TAC by Telephone 18
- Product Overview 19
- 1.1.1 Features 21
- 1.1.2 Configurations 21
- 1.1.2.3 IMA Configuration 22
- Subtending host 27
- Cisco 6260 System Overview 28
- 1.2.2 Cisco 6260 Connectors 30
- 1.2.3 Cisco 6260 Cards 31
- 1.2.3.1.1 Faceplate Features 32
- 1.2.3.2.1 Faceplate Features 34
- 1.2.3.3.1 Faceplate Features 36
- 1.2.3.4.1 Faceplate Features 38
- 1.2.3.5.1 Faceplate Features 40
- 1.2.3.6.1 Faceplate Features 42
- 1.2.3.7.1 Faceplate Features 44
- NI2-155MM-155MM2 Only 47
- 1.2.3.9.1 Faceplate Features 49
- 1.2.3.13 Redundancy Overview 57
- 1.2.4 Cisco 6260 I/O Modules 59
- Figure 1-19 E3 I/O Module 60
- Figure 1-20 E3 I/O Module 61
- Figure 1-21 OC-3c I/O Module 61
- 1.2.5 PEM 63
- Figure 1-23 PEM Faceplate 64
- 1.2.6 Fan Tray 65
- 1.2.8 ESD Jack 66
- 1.2.7 Air Filters 66
- 1.3 Management Software 67
- Management Software 68
- Preparing for Installation 69
- 2.1.2 Warning Definition 70
- Safety Requirements 71
- 2.1.4.1 Hot Swapping Cards 78
- 2.2 Site Requirements 79
- 2.2.1.2 Ventilation 80
- 2.2.1.3 Space 81
- 2.2.2 Power Requirements 82
- Site Requirements 83
- Required Tools and Equipment 84
- 2.5 Verifying Contents 86
- 2.6 Inspecting for Damage 86
- Inspecting for Damage 87
- 3.1 Installation Checklist 90
- 3.2 Installation Procedures 91
- 3.2.6 Ground the Cisco 6260 95
- Negative connection (–) 101
- Positive connection (+) 101
- Ground connection ( ) 101
- 3.2.12 Apply Power 102
- –48V on the voltmeter 103
- Installation Procedures 108
- 3.2.19.1 Before You Begin 110
- Splitter Configuration 117
- 4.1 Installation Checklist 118
- 4.2 Installation Procedures 118
- Bracket orientation for 120
- ETS 600-mm rack 120
- Bracket orientation 120
- Cisco 6260 122
- 4.2.5 Ground the Cisco 6260 123
- 0.43 in 126
- 4.2.9 Apply Power 129
- 4.2.16.1 Before You Begin 137
- Troubleshooting 145
- 5.2 Basic Checks 146
- 5.4 System-Wide Problems 147
- OL-2365-01 148
- System-Wide Problems 148
- 5.5 FRU-Specific Problems 152
- FRU-Specific Problems 153
- 5.5.3 Line Card Problems 154
- 5.5.4 I/O Module Problems 158
- 5.5.5 Fan Tray Problems 159
- 5.5.6 PEM Problems 160
- 5.6 Alarms 161
- Table 5-17 IMA Group Alarms 164
- Table 5-20 Power Alarms 165
- Cisco 6260 System 167
- 6.2 Fan Tray Maintenance 168
- Fan Tray Maintenance 170
- 6.3.1 xTU-C Line Card 173
- Unlocked 174
- 6.3.2 DS3/2DS3 NI-2 Card 175
- 6.3.4 OC-3c/OC-3c NI-2 Card 181
- 6.3.5 I/O Module 183
- 6.3.6 PEM 186
- 6.3.6.2 Removing the PEM 188
- Technical Specifications 189
- A.1.1 Cisco 6260 Chassis 190
- Hardware Specifications 192
- A.1.9 DS3/2DS3 NI-2 Card 196
- A.1.12 I/O Module 199
- A.1.13 PEM 199
- A.2 Software Specifications 200
- Port Mapping Specifications 201
- Port Mapping Table 202
- Standard Telco Color Chart 206
- C.1 xDSL Connectors 209
- C.2 I/O Module Connectors 209
- • BITS clock input circuits 211
- RJ-45 female 212
- C.5 Ethernet Port 213
- Ethernet Port 214
- Numerics 215
- Glossary 216
Produits connexes et manuels pour Mise en réseau Cisco 6260
Mise en réseau Cisco 815 Spécifications
(28 pages)
(28 pages)
(21 pages)
Mise en réseau Cisco ME 3800X Spécifications
(622 pages)
(622 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.304 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels