Cisco 4500M Guide d'installation Page 215
- Page / 270
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Cabling Specifications A-75
HSSI Cable Pinouts
In addition to these cables, some connections require bare-wire connections (directly to
terminal posts). See the E1-G.703/G.704 network processor module configuration note for
complete information.
HSSI Cable Pinouts
Two types of cables are available for use with an HSSI network processor module:
• CAB-HSI1=, an HSSI cable used to connect your router to an external DSU (and the
HSSI network)
• CAB-HNUL=, a null-modem HSSI cable used to connect two routers back-to-back.
The Cisco 4000 series router can connect a Cisco 7000 family HIP, PA-H, or PA-2H.
HSSI Interface Cable
Figure A-14 shows the HSSI cable (product number CAB-HSI1= and part number
72-0710-xx). Table A-27 provides pinouts. The cable has a male DB-50 (SCSI) connector
on each end.
Figure A-14 HSSI Interface Cable Connectors
Table A-27 HSSI Interface Cable Pinouts
Signal Name
Pin No. + Side
(Router End)
Direction
1
Pin No. – Side
(DSU End)
SG (Signal Ground) 1 — 26
RT (Receive Timing) 2 <— 27
H5691
- About This Guide 1
- Document Organization 2
- Document Conventions 3
- Overview of the Cisco 4000 5
- Series Routers 5
- Series Specifications 8
- Software Compatibility 10
- Series Specifications 12
- Memory Systems 13
- Shared Memory Requirements 15
- Main Memory Requirements 17
- Cisco RPS Support 18
- Overview 19
- Fully Redundant Power 20
- RPS Features 21
- Preparing to Install 23
- Cisco 4000 Series Routers 23
- Safety with Electricity 24
- Safety Recommendations 25
- General Site Requirements 26
- Site Configuration Precautions 27
- Equipment Racks 28
- Power Supply Features 28
- Installation Checklist 29
- Site Log 30
- Required Tools and Equipment 30
- Inspecting the System 31
- • This publication 32
- • Cisco Information Packet 32
- Configuring the Cisco 4000 33
- Series Chassis 33
- Removing the Component Tray 34
- Replacing the Component Tray 41
- Making External Connections 43
- Unit Numbering 44
- AUX CONSOLE 46
- Use of the Slot Filler Panel 47
- Considerations 48
- Console Port Connections 49
- Auxiliary Port Connections 49
- Ethernet Connections 50
- Connectors 51
- Connection 52
- ETHERNET AUI 54
- Six-Port Ethernet Module 55
- Token Ring Connections 56
- IN-RING A 57
- IN-RING B 57
- Serial Connections 59
- EIA/TIA-232 Connections 60
- EIA/TIA-449 Connections 61
- V.35 Connections 62
- X.21 Connections 62
- EIA-530 Connections 63
- Interference Considerations 63
- Configuring Serial Connections 64
- Router connections 66
- EIA/TIA-449 V.35 X.21 66
- EIA/TIA-232 EIA-530 66
- G.703/G.704 Cable Connections 72
- • Multimode dual-attachment 74
- • Multimode single-attachment 74
- • Single-mode dual-attachment 74
- Connectors—End View 76
- CLASS 1 LASER PRODUCT 77
- LASERKLASSE 1 77
- OPT-BYPASS 79
- 87654321 81
- 1. kHz = kilohertz 82
- 2. nF = nanoFarad 82
- LOOPBACK 83
- LOCAL ALARM 83
- REMOTE ALARM 83
- T1 Cabling 84
- E1 Cabling 87
- ATM Connections 88
- XMTR RCVR 89
- RX ALARM 89
- RX CELLSBUSY 89
- RX CELLS 90
- ATM Cabling 91
- Figure 4-54 ST2 Connector 92
- Simplex (2) 94
- Duplex (1) 94
- BNC to RCVR 94
- BNC to XMTR 94
- Power Budget 97
- 500 MHz/km 98
- Single-Mode Transmission 101
- For Further Reference 102
- AC power supply 103
- DC power supply 104
- Terminal block cover 104
- Powering Up the Router 107
- Software Configuration 109
- Configuring the Router 111
- Configuring the Router 112
- Software Configuration 5-5 113
- Software Configuration 5-9 117
- Additional Configuration Tasks 118
- Software Configuration 5-11 119
- Configuring the T1 Interface 121
- Configuring the E1 Interface 123
- • Network protocol addresses 126
- Software Configuration 5-23 131
- Software Configuration 5-25 133
- Router# config terminal 134
- Router(config)# 134
- Router(config-if)# 134
- Router# disable 136
- Router> 136
- Software Configuration 5-29 137
- Software Configuration 5-31 139
- If You Need More Information 140
- Cabling Specifications 141
- 1. GND = Ground 143
- 2. CD = Carrier Detect 143
- Serial Cables 145
- <— indicates DCE to DTE 165
- DCE to DTE 172
- E1-G.703/G.704 Cable Pinouts 214
- HSSI Cable Pinouts 215
- HSSI Null- Modem Cable 216
- Ethernet Cable Pinouts 218
- 10BaseT Connector Pinouts 219
- 100BaseT Connector Pinouts 220
- 8 7 6 5 4 3 2 1 221
- Jackscrew Pin 21 223
- Token Ring Port Pinouts 225
- BRI Pinouts 226
- Channelized T1 Pinouts 227
- Channelized E1 Pinouts 228
- Replacing Memory in 233
- Replacing Main Memory SIMMs 236
- Removing Main Memory SIMMS 237
- Top view 238
- Front of the chassis 238
- Side view 238
- Installing Main Memory SIMMs 239
- Replacing Shared-Memory SIMMs 241
- Side view, SIMM inserted 243
- Helper Flash Memory SIMM 244
- Polarization notch 245
- System-code SIMM card 245
- Installing Flash-Memory SIMMs 246
- Figure C-9 Boot ROM Locations 249
- Cisco 4000 Series Virtual 251
- Configuration Register 251
- • Recover a lost password 252
- Configuring the Boot Field 254
- Cisco 4000-M ROM Monitor 259
- Cisco 4000-M ROM Monitor E-3 261
- > t m 262
- Running the Diagnostics 263
- Cisco 4500-M and 265
- Cisco 4700-M ROM Monitor 265
- Debugging Commands 268
Produits connexes et manuels pour Mise en réseau Cisco 4500M
(2 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels