Cisco XR 12410 Manuel d'utilisateur Page 122
- Page / 238
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 3 Installing the Cisco XR 12410 Router
Connecting PRP Route Processor Cables
3-40
Cisco XR 12410 and Cisco XR 12810 Router Installation Guide
OL-17441-01
Note RP cables are not available from Cisco, but are available from any commercial
cable vendor.
Note To comply with the intra-building lightning surge requirements of
GR-1089-CORE, Issue
II, Revision 01, February 1999, you must use a shielded
cable when connecting to the console, auxiliary, and Ethernet ports. The shielded
cable is terminated by shielded connectors on both ends, with the cable shield
material tied to both connectors.
Connecting to the PRP Console Port
The system console port on the PRP is a DCE RJ-45 receptacle for connecting a
data terminal to perform the initial configuration of the router. The console port
requires a straight-through RJ-45 cable.
See the “PRP Auxiliary and Console Port Connections” section on page 2-22 for
additional information about the console port.
Refer to Figure 3-28 and use the following procedure to connect a data terminal
to the PRP console port.
Step 1 Set your terminal to these operational values: 9600 bps, 8 data bits, no parity,
2
stop bits (9600 8N2).
Step 2 Power off the data terminal.
Step 3 Attach the terminal end of the cable to the interface port on the data terminal.
Step 4 Attach the other end of the cable to the PRP console port.
Step 5 Power on the data terminal.
- Router Installation Guide 1
- CONTENTS 5
- B Site Log B-1 9
- Contents 10
- OL-17441-01 10
- Changes to This Document 11
- Audience 12
- Document Organization 12
- Document Conventions 13
- Product Overview 15
- AC and DC Power Subsystems 19
- Figure 1-4 AC PEM Components 20
- DC Power Supplies 21
- • 2 alarm cards 23
- Clock Scheduler Card 24
- Alarm Cards and Alarm Display 25
- Line Cards 28
- Route Processor 28
- BITS 1 AUX CONSOLE 33
- PRP-3 LEDs 34
- PRP Memory Components 37
- PRP SDRAM 41
- PRP SRAM 42
- PRP NVRAM 42
- PRP Flash Memory 42
- PRP-3 Compact Flash 43
- XR 12000 Series Router 44
- Horizontal cable 46
- Blower Module 47
- Figure 1-18 Cooling Air Flow 48
- Preparing for Installation 51
- Safety Guidelines 52
- Laser Safety 53
- Lifting Guidelines 55
- Site Requirement Guidelines 56
- Enclosed Rack 57
- Open Rack 57
- Telco Rack 58
- Center-mount 59
- Rack-mount bracket 59
- (attached to rack posts) 59
- 18.95 in 61
- 26.533 in 61
- 7.735 in 61
- 18.798 in 61
- Air Flow Guidelines 62
- Power Connection Guidelines 63
- AC-Powered Routers 64
- DC-Powered Routers 65
- Figure 2-8 DC Power Cable Lug 66
- Site Wiring Guidelines 70
- PRP Auxiliary Port Signals 74
- PRP Console Port Signals 75
- PRP Ethernet Connections 76
- 8 7 6 5 4 3 2 1 78
- Transmission 80
- Installation Overview 85
- Required Tools and Equipment 86
- 1 Front Door Latch 87
- Removing Power Supplies 89
- Removing DC PEMs 90
- Removing the Blower Module 91
- Verifying Rack Dimensions 99
- Reinstalling Power Supplies 109
- Reinstalling AC PEMs 110
- Reinstalling DC PEMs 111
- Air filter door 114
- Clock scheduler card 114
- FAST ETERNET 118
- Alarm display 125
- Troubleshooting Overview 132
- Identifying Startup Issues 134
- Figure 4-1 AC PEM Components 136
- Troubleshooting a DC PEM 140
- 1 3 4 52 6 146
- 1 3 4 52 146
- ETH 1ETH 0 148
- PRP Reset Switch 149
- PROCESSOR 150
- PRP-3 Alphanumeric LEDs 154
- Single PRP-3 Scenario 154
- Dual PRP-3 Scenario 156
- Troubleshooting Line Cards 159
- Figure 4-11 Cooling Air Flow 167
- Blower Module Operation 168
- Power Supply Operation 168
- Overtemperature Conditions 169
- Maintaining the Router 173
- Powering Off the Router 174
- OC-12/STM-4 ATM 178
- Subsystem Components 184
- Figure 5-7 AC PEM Components 186
- Figure 5-11) 192
- Rear panel 193
- AC horizontal trough 193
- DC horizontal trough 204
- Clear plastic covers 204
- Card Cage 212
- Technical Specifications 219
- • chassis only 220
- Router Specifications 224
- Site Log 225
- Appendix B Site Log 226
- Numerics 229
Produits connexes et manuels pour Matériel Cisco XR 12410
(2 pages)
Matériel Cisco 7300-6T3 Manuel d'utilisateur
(54 pages)
(54 pages)
Matériel Cisco 3545 MCU Manuel d'utilisateur
(56 pages)
(56 pages)
Matériel Cisco 3000 Manuel d'utilisateur
(16 pages)
(16 pages)
Matériel Cisco 340 Manuel d'utilisateur
(62 pages)
(62 pages)
Matériel Cisco 4000 Manuel d'utilisateur
(18 pages)
(18 pages)
Matériel Cisco 3620 Manuel d'utilisateur
(12 pages)
(12 pages)
Matériel Cisco 350 Manuel d'utilisateur
(12 pages)
(12 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels