Cisco 12000 Series Manuel d'utilisateur télécharger pdf (Page 7)

5-7

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007

Chapter 5 Installing and Removing a Shared Port Adapter

Checking the Installation

When you reinsert the SIP, the system automatically brings up the interfaces that were up

when the SIP was removed.

Router#

18:05:00: %OIR-6-INSCARD: Card inserted in slot 3, interfaces administratively shut down

18:05:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3/0, changed state

to up

Note When a new SIP is inserted or when a SIP is moved to a new slot, the system recognizes the new

interfaces but leaves them in the shutdown state until you configure them and change their state to up.

The following sample display shows the events logged by the system as you insert a new SIP in module

slot 3.

Router#

18:05:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3/1, changed state

to down

Use the following procedure to verify that the SIP is installed correctly:

Step 1 Observe the console display messages and verify that the system discovers the SIP, while the system

reinitializes each interface, as follows:

• If you installed a new SIP, the STATUS LED should be on (green). The system should recognize all

new interfaces but leave them configured as down.

• If you replaced a SIP, the STATUS LED should be on (green). The system does not recognize each

interface and places it in the administratively down state.

Step 2 Verify that the ENABLED LED on the SPA goes on (is green) and remains on after the reinitialization

is complete. If the ENABLED LED remains on, proceed to Step 5. If the ENABLED LED does not

remain on, proceed to Step 3.

Step 3 If the ENABLED LED on a SPA fails to go on, the SPA or the SIP might not be fully seated even if the

SPA lock is in the locked and horizontal position. When a SPA is not recognized, the SIP is deactivated,

and its OIR LED is yellow.

• Remove the SIP from the router.

• Remove the SPA from the SIP.

• Inspect the SIP and the SPA. Verify there are no bent pins or parts and that there is nothing lodged

in the two devices that could prevent a good connection.

• Insert the SPA in the SIP by sliding the SPA all the way in the SIP until the SPA is firmly seated in

the SPA interface connector. When fully seated in the SIP, the SPA might be slightly behind the SIP

faceplate.

• Insert the SIP into the router.

• After the system reinitialization, the ENABLED LED on the SPA should go on and remain on. If the

ENABLED LED remains on, proceed to Step 5. If it does not, proceed to Step 4.

Step 4 If the ENABLED LED on a SPA still fails to go on, remove the SIP and install it in another available

slot on the router.

• If the ENABLED LED goes on, suspect a failed backplane port in the original slot.

• If the ENABLED LED fails to go on, remove the SIP and ensure the SPA is firmly seated in its slot.

Remove and reinstall it accordingly.

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Modèles	Type de document
KFC-W3010	Manuel de l'utilisateur Kenwood KFC-W3010 User Manual [es] , 2 pages
KFC-XW1224D	Manuel de l'utilisateur Инструкция по эксплуатации Kenwood KFC-XW1224D, 2 pages
KFC-S502P	Manuel de l'utilisateur Инструкция по эксплуатации Kenwood KFC-S502P, 2 pages
KSC-8803	Manuel de l'utilisateur Kenwood KSC-8803 User Manual, 2 pages
KSC-9903	Manuel de l'utilisateur Kenwood KSC-9903 User Manual, 2 pages

Cisco 12000 Series Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Kenwood MFJ-286 manuels

Kenwood MFJ-286 Manuel de l'utilisateur (1 pages)

Table des matières

Plus de produits et de manuels pour Microphones Kenwood

Cisco 12000 Series Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Cisco 12000 Series

Kenwood MFJ-286 manuels

Kenwood MFJ-286 Manuel de l'utilisateur (1 pages)

Table des matières

Plus de produits et de manuels pour Microphones Kenwood