Cisco ASR 1004 Manuel d'utilisateur

QUICK START GUIDECisco ASR 1004 Router1 Documentation and Resources2 Prepare for Installation3 Rack-Mount the Router4 Connect the Router to the Networ

10Figure 5 Attaching the Cable-Management Bracket to the Cisco ASR 1004 RouterStep 3 Using the bottom rack-mount ear hole, insert the screw through ca

11Figure 6 Chassis Ground Lug Location on the Cisco ASR 1004 RouterUse the following procedure to attach the grounding lug to the chassis ground conne

12Step 5 Locate the chassis ground connector on the side of your chassis. Step 6 Insert the two screws through the holes in the grounding lug.Step 7 U

13Step 2 After you establish normal router operation, you can disconnect the terminal.Note For console and auxiliary port pinouts, see Appendix A in t

14Step 3 Insert an Ethernet RJ-45 cable into the MGMT ETHERNET port.Step 4 Insert the other end of the RJ-45 cable to your management device or networ

15Step 2 Tighten the captive installation screws.Step 3 Insert the AC power cable into the power supply inlet.Step 4 Plug the power supply cable into

16WarningWhen installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046WarningThis equip

17Figure 10 shows the DC power supply for the Cisco ASR 1004 Router.DC Power Supply for the Cisco ASR 1004 RouterNote Shielded cables must be used to

18Figure 11 DC Power Supply Grounding Stud Location and Connection on the Cisco ASR 1004 RouterStep 1 Make certain that the chassis ground is connecte

19Figure 12 Cisco ASR 1004 Router DC Power Supply Terminal BlockCaution Before you continue to install the terminal block wires, stop and perform Step

21 Documentation and ResourcesDocumentation for the Cisco 1000 Series Aggregation Services Routers documentation is online with the exception of the

20Step 8 Connect the other ends of the terminal block cables to the site ground connection. Move the circuit-breaker switch to the On position (|).Thi

21Start the Cisco ASR 1004 RouterAfter installing your Cisco ASR 1004 Router and connecting cables, start the router as follows.Step 1 Check for the f

22Note The system boots differently depending on the configuration that ships with your system. Example one in this section shows the system being boo

23licensed under the GNU General Public License ("GPL") Version 2.0. Thesoftware code licensed under GPL Version 2.0 is free software that c

24*Feb 19 17:35:19.171: %ASR1000_OIR-4-INSCARD: Card (fp) inserted in slot F0*Feb 19 17:35:19.171: %ASR1000_OIR-4-ONLINECARD: Card (fp) online in slot

25Step 1 Connect a console terminal to the console port and then boot the router. The system boots from flash memory. The following information appear

26 Configure CLNS? [no]: Configuring interface parameters: Do you want to configure GigabitEthernet0/0/0 interface? [yes]: n Do you want to configu

27!interface FastEthernet0/3/4shutdownno ip address!interface FastEthernet0/3/5shutdownno ip address!interface FastEthernet0/3/6shutdownno ip address!

28Receiving images/packages_crypto/asr1000rp1-advipservicesk9.mcp_dev_20080109_101550.bin from 2.0.0.2 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

29cisco ASR1004 (RP1) processor with 548011K/6147K bytes of memory.8 FastEthernet interfaces6 Gigabit Ethernet interfaces32768K bytes of non-volatile

32 Prepare for InstallationThis section contains information about tools and parts, warnings, site preparation information, and information for rack-

30Perform Other Configuration TasksTo make advanced configuration changes after you establish the basic startup configuration for your router, refer t

31Step 5 Remove any power cables from the Cisco ASR 1004 Router. a. For power supplies with a circuit breaker switch, position the switch to the Off (

32Step 5 The power supply LEDs light when power is supplied to the router.You have completed a live change-out procedure (that is, removing and replac

33You have removed a DC power supply from the Cisco ASR 1004 Router and now must replace the DC power supply within five minutes. This section provide

34Figure 14 Cisco ASR 1004 Router DC Power Supply Terminal BlockStep 8 Tighten the Kepnut screw (use the screwdriver to tighten the ground screw in th

35Figure 15 Cisco ASR 1004 Router DC Power Supply Terminal BlockStep 11 Remove the tape from the circuit-breaker switch handle and move the circuit-br

36Remove the Shared Port Adapter The shared port adapter ships installed. These instructions are provided for future use. Cabling information is inclu

37Note If the shared port adapter fails to come up, reseat or reinsert the shared port adapter: do not use excessive force. Step 8 Power on the router

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0

4Prepare for Rack-Mount InstallationBefore you begin the rack-mounting tasks:• Decide whether or not you want to front- mount or rear-mount the chassi

5Step 6 To install the Cisco ASR 1004 Router in an equipment rack, see “Four-Post Rack Installation” section on page 6 or “Two-Post Rack Installation”

6Four-Post Rack InstallationThis section describes the types of racks used for rack-mounting the chassis.Figure 3 Installing the Cisco ASR 1004 Router

7Step 5 Lift the chassis into position between the rack posts (requires two people).Step 6 Align the mounting bracket holes with the rack post holes a

8Two-Post Rack InstallationThe Cisco ASR 1004 Router can be installed in a two-post rack, either 19 inch or 23 inch.Note Inner clearance (the width be

9Step 4 Hold the chassis in position against the mounting rails and follow these steps:a. Insert the bottom screw into the third hole up from the bott